<![CDATA[SoliForum - 3D Printing Community — Slic3r supports]]> https://www.soliforum.com/topic/6742/slic3r-supports/ Sat, 05 Jul 2014 18:19:07 +0000 PunBB <![CDATA[Re: Slic3r supports]]> https://www.soliforum.com/post/59815/#p59815 The cura settings?
I will have to look, I don't think I did anything special besides making the first move a g1 z5 so that on the first rapid it did not bang the glass with the interpolated xyz simultaneous move.

]]> Sat, 05 Jul 2014 18:19:07 +0000 https://www.soliforum.com/post/59815/#p59815 <![CDATA[Re: Slic3r supports]]> https://www.soliforum.com/post/59807/#p59807 joshj wrote:

I have done 8+ hour prints with no issues.  If there is an issue it is not specifically with cura. It only is a gcode generator after all.


hi did you publish your settings anywhere,
i'd love to run with cura but i still have Z axis issue
thanks

]]> Sat, 05 Jul 2014 16:16:47 +0000 https://www.soliforum.com/post/59807/#p59807 <![CDATA[Re: Slic3r supports]]> https://www.soliforum.com/post/59117/#p59117 I have done 8+ hour prints with no issues.  If there is an issue it is not specifically with cura. It only is a gcode generator after all.

]]> Sun, 22 Jun 2014 21:50:42 +0000 https://www.soliforum.com/post/59117/#p59117 <![CDATA[Re: Slic3r supports]]> https://www.soliforum.com/post/59103/#p59103 I read into it, isn't there an issue with cura stopping halfway thru the print?

]]> Sun, 22 Jun 2014 03:16:02 +0000 https://www.soliforum.com/post/59103/#p59103 <![CDATA[Re: Slic3r supports]]> https://www.soliforum.com/post/59102/#p59102 Look into cura also just for prints that require support.

]]> Sun, 22 Jun 2014 03:10:52 +0000 https://www.soliforum.com/post/59102/#p59102 <![CDATA[Re: Slic3r supports]]> https://www.soliforum.com/post/58810/#p58810 I changed the overhang to 45° and it did everything I needed it to. I'll see if it works on other stuff but this is all I wanted for this print

]]> Wed, 18 Jun 2014 00:30:30 +0000 https://www.soliforum.com/post/58810/#p58810 <![CDATA[Re: Slic3r supports]]> https://www.soliforum.com/post/58786/#p58786 1.0.1

]]> Tue, 17 Jun 2014 15:33:31 +0000 https://www.soliforum.com/post/58786/#p58786 <![CDATA[Re: Slic3r supports]]> https://www.soliforum.com/post/58782/#p58782 What version of Slic3r are you using?

]]> Tue, 17 Jun 2014 15:02:11 +0000 https://www.soliforum.com/post/58782/#p58782 <![CDATA[Slic3r supports]]> https://www.soliforum.com/post/58760/#p58760 Does anyone know how to enable some sort of simpler support system? Sorta like the supports that only go under the major overhangs? I am trying to print a very detailed print, but the gcode generated by slicer covers almost everything with support material? Any suggestions?

]]> Mon, 16 Jun 2014 23:55:02 +0000 https://www.soliforum.com/post/58760/#p58760