<![CDATA[SoliForum - 3D Printing Community — X axis endstop hit on echo- doesn't home correctly]]> https://www.soliforum.com/topic/640/x-axis-endstop-hit-on-echo-doesnt-home-correctly/ Tue, 27 Nov 2012 19:45:08 +0000 PunBB <![CDATA[Re: X axis endstop hit on echo- doesn't home correctly]]> https://www.soliforum.com/post/5721/#p5721 Glad you resolved it. That log message shows the same date as the latest copy on github. I don't always change the date in the configuration.h file on update.

]]> Tue, 27 Nov 2012 19:45:08 +0000 https://www.soliforum.com/post/5721/#p5721 <![CDATA[Re: X axis endstop hit on echo- doesn't home correctly]]> https://www.soliforum.com/post/5676/#p5676 > 8:55:29 AM: N1 M110 *2
< 8:55:29 AM: echo:Marlin 1.0.0
> 8:55:29 AM: N2 M115 *4
< 8:55:29 AM: echo: Last Updated: 2012-09-17 | Author: Lawsy
< 8:55:29 AM: echo: Free Memory: 12512  PlannerBufferBytes: 1232
> 8:55:29 AM: N4 M111 S6 *67
< 8:55:29 AM: echo:Using Default settings:


Showed up in the Repetier log upon connecting.
I am assuming this was a previous firmware that you had uploaded, but not the current one.

]]> Tue, 27 Nov 2012 13:59:10 +0000 https://www.soliforum.com/post/5676/#p5676 <![CDATA[Re: X axis endstop hit on echo- doesn't home correctly]]> https://www.soliforum.com/post/5672/#p5672 Didn't notice the message- where would that show up? Using Repetier, but the problem was solved by unplugging then reinserting the x-axis endstop. Loose connection. Come to think of it, I was getting the same thing on the z axis after I took out the board to swap chips- that time I had inadvertently plugged it into only two of the three pins- that was pretty easy to spot.

]]> Tue, 27 Nov 2012 11:57:40 +0000 https://www.soliforum.com/post/5672/#p5672 <![CDATA[Re: X axis endstop hit on echo- doesn't home correctly]]> https://www.soliforum.com/post/5659/#p5659 When you connect to the printer, does it give a message in the log about Solidoodle and a link to my github?

If it does not, the firmware is still the version set up for a Mendel that comes on the 1284P.

Are you using Repetier? Perhaps there is a homing setting set incorrectly there, although that would be less likely if it was working before.

]]> Tue, 27 Nov 2012 04:46:38 +0000 https://www.soliforum.com/post/5659/#p5659 <![CDATA[X axis endstop hit on echo- doesn't home correctly]]> https://www.soliforum.com/post/5655/#p5655 So I updated the firmware (I think) successfully, on the 1284 chip, but after doing so I can no longer home x axis. It always moves to the right, and gives an echo of "x axis endstop hit". Tried swapping endstops with y, and it still gives an echo for x. When the endstops are not switched, y and z home correctly. When attempting to print, x axis just slams to the left and drips plastic everywhere. Any ideas? thanks in advance

]]> Tue, 27 Nov 2012 04:07:41 +0000 https://www.soliforum.com/post/5655/#p5655