SoliForum - 3D Printing Community — Turn off or down heat on print bed during print?

Re: Turn off or down heat on print bed during print?

null@example.com (AZERATE) — Fri, 25 Apr 2014 02:03:35 +0000

I have gotten some good results from this method using PLA, but only in trials for prototypes.
After about 15-20 layers, I shut the bed off and worked great....but I still used wardjr's methods.

For ABS, don't skimp on the heat!

Re: Turn off or down heat on print bed during print?

null@example.com (wardjr) — Fri, 25 Apr 2014 01:25:30 +0000

Yep, a good thick coat on the bottom of the glass will stick it to the bed after a couple heat/cool cycles and a light mist on the top will help your prints stick

Re: Turn off or down heat on print bed during print?

null@example.com (MartinFahrer) — Fri, 25 Apr 2014 01:20:55 +0000

wardjr wrote:

Leave the tape go have a cheap piece of glass not even 1/8 and spray the underside with aqua net and stick it to the bed. A couple of heat/cool cycles and it won't move unless you want to remove it. Set up correctly this will be your most cost effective mod.

Thanks. I still use hairspray on the glass tight?

Re: Turn off or down heat on print bed during print?

null@example.com (wardjr) — Thu, 24 Apr 2014 21:34:49 +0000

Leave the tape go have a cheap piece of glass not even 1/8 and spray the underside with aqua net and stick it to the bed. A couple of heat/cool cycles and it won't move unless you want to remove it. Set up correctly this will be your most cost effective mod.

Re: Turn off or down heat on print bed during print?

null@example.com (MartinFahrer) — Thu, 24 Apr 2014 21:29:07 +0000

My thought was turn it down to 50 and see what happens. I don't have a glass bed I have the tape bed. If I get class do I have to take the tape off. I was think a peice of 1/8" glass any thoughts

Re: Turn off or down heat on print bed during print?

null@example.com (Serin) — Thu, 24 Apr 2014 12:29:26 +0000

Nothing wrong with a little bit of experiment guys.
That's the true scientific method, and it's best used when one can prove a fact to oneself.

Re: Turn off or down heat on print bed during print?

null@example.com (wardjr) — Thu, 24 Apr 2014 03:26:28 +0000

ronsii wrote:

wardjr wrote:
The result will be once the bed and print reach room temp the part will be loose.
+1 tried it long ago

I think most of us are using that with glass to our advantage

Re: Turn off or down heat on print bed during print?

null@example.com (ronsii) — Thu, 24 Apr 2014 03:23:54 +0000

wardjr wrote:

The result will be once the bed and print reach room temp the part will be loose.

+1 tried it long ago

Re: Turn off or down heat on print bed during print?

null@example.com (wardjr) — Thu, 24 Apr 2014 03:21:08 +0000

The result will be once the bed and print reach room temp the part will be loose.

Re: Turn off or down heat on print bed during print?

null@example.com (MartinFahrer) — Wed, 23 Apr 2014 23:57:23 +0000

DePartedPrinter wrote:

MartinFahrer wrote:
I heard after a few layers of printing it's ok to turn the print bed down/ off with ABS filament.

Missinformation is apparently rampant when it come to 3D printing. I agree with wardjr, reducing the heat will only aggravate the situation...
What temp do you have your bed set at?

Actually it was not on the forums but at the 3D printing expo in NYC. The theory is that once I think 10 layers are printed the object is already stuck to the bed. I do know after the bed is cooled the model still needs to be pried from the bed. I am going to experiment this weekend and will post the results.

Re: Turn off or down heat on print bed during print?

null@example.com (DePartedPrinter) — Wed, 23 Apr 2014 20:06:38 +0000

MartinFahrer wrote:

I heard after a few layers of printing it's ok to turn the print bed down/ off with ABS filament.

Missinformation is apparently rampant when it come to 3D printing. I agree with wardjr, reducing the heat will only aggravate the situation...

What temp do you have your bed set at?

Re: Turn off or down heat on print bed during print?

null@example.com (wardjr) — Wed, 23 Apr 2014 15:23:27 +0000

MartinFahrer wrote:

I heard after a few layers of printing it's ok to turn the print bed down/ off with ABS filament. has anyone tried this how many layers to you think it should print before turning the heat down. I am having some curling issues.

If by curling you are referring to parts of the print lifting off the bed than reducing heat will only aggravate the situation. If you are referring to areas of your print (corners) rising up so the nozzle drags across it than bed heat isn't the cause. For that you need to reduce the speed to give the plastic more time to cool before the next layer goes down.

Turn off or down heat on print bed during print?

null@example.com (MartinFahrer) — Wed, 23 Apr 2014 15:09:36 +0000

I heard after a few layers of printing it's ok to turn the print bed down/ off with ABS filament. has anyone tried this how many layers to you think it should print before turning the heat down. I am having some curling issues.