SoliForum - 3D Printing Community — Noob with no idea how to start :(

Re: Noob with no idea how to start :(

null@example.com (diyengineer) — Fri, 28 Feb 2014 10:06:28 +0000

Without this forum i think i would have been dead in the water also, or would have taken months to figure something out haha. If your new and have a question just ask, we may also have the same question! lol

Re: Noob with no idea how to start :(

null@example.com (auslander68) — Thu, 27 Feb 2014 04:54:03 +0000

I'm a little over a month into the learning curve and even though I've been printing almost every day I'm still learning a lot. This forum and the people in it were a major factor in going with a solidoodle. A lot of what I'm learning is really just making sense of what the more advanced people are discussing. It really is like drinking from a fire hose. Whenever I hit something I can't figure out on my own, a couple quick searches on this forum usually gets me sorted out.

Good luck!

Re: Noob with no idea how to start :(

null@example.com (ggunners) — Tue, 25 Feb 2014 16:37:11 +0000

If your print hasn't failed, you're not printing. Even successful prints may have slicing settings that would make them even better. Knowing what to fine tune comes from experience.

Re: Noob with no idea how to start :(

null@example.com (mikefree41) — Tue, 25 Feb 2014 16:33:42 +0000

Go to Hobby Lobby and buy a few 8" mirrors, buy a can of cheap hair spray. Take your time and don't worry about failures.

Re: Noob with no idea how to start :(

null@example.com (titanv11) — Mon, 24 Feb 2014 10:28:57 +0000

Thankyou Adrian 4 clarifying that 4 me...
Your absolutely correct (frustration got the better of me).

I will vent my frustrations where they belong

The links provided DO help and this forum has an immense amount of relevant information available.
(tomorrow am looking 4 a sheet of glass 4 the hot bed... lol)

Thanks again

Re: Noob with no idea how to start :(

null@example.com (adrian) — Mon, 24 Feb 2014 05:55:10 +0000

This forum has no affiliation to Solidoodle who took your money and sent the printer.. So you might want to address your comments directly at Solidoodle customer service as this is a volunteer community with nothing to do with formal support of you printer, collecting your money, or what documentation isn't sent...

We are all generally happy to try and help, but issues with the lack of supplied documentation should go to the people who got you money - they really should start working for it

Hope the links provided help and have fun getting to your first print... its addictive.

Re: Noob with no idea how to start :(

null@example.com (titanv11) — Mon, 24 Feb 2014 05:49:38 +0000

Thankyou to both...

BUT seriously at LEAST have a sticky thread 4 new owners.....

Re: Noob with no idea how to start :(

null@example.com (Claghorn) — Sun, 23 Feb 2014 16:49:41 +0000

If you want to see my adventures starting from scratch, I recorded them here:

http://home.comcast.net/~tomhorsley/har … e-log.html

Re: Noob with no idea how to start :(

null@example.com (adrian) — Sun, 23 Feb 2014 10:14:59 +0000

Howdies - Work your way through http://wiki.solidoodle.com/gettingstarted and see where you end up.

And yes it comes with nuthin' ..

Noob with no idea how to start :(

null@example.com (titanv11) — Sun, 23 Feb 2014 09:35:17 +0000

I recently purchased a SD4 but have never used a 3D printer and dont know anyone that owns or knows how to use one
The 3D printer arrived... BUT no instructions.. no manual... no software/CD...
Should the item have had these things in the box??

so basically, is there an area or site that details how to get started.

I purchased this just out of 3D curiosity, and am very computer literate.

I know there are procedures for setting up that must be done but no idea where to start or what to do.

Can someone please point me in the right direction.