<![CDATA[SoliForum - 3D Printing Community — Assemblying my FilaStruder]]> https://www.soliforum.com/topic/5201/assemblying-my-filastruder/ Mon, 03 Feb 2014 19:04:54 +0000 PunBB <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48565/#p48565 1kg/12 hours is an estimate, not a guarantee. Depends on a lot of things - extrusion temperature, polymer MFI, etc. You're pretty close, about 0.75kg/12hr.

]]> Mon, 03 Feb 2014 19:04:54 +0000 https://www.soliforum.com/post/48565/#p48565 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48558/#p48558 Guys,

I am getting around 13cm / minute here.

Still... it wouldn't make 1kg / 12 hours.

If we say that:
Density: 1.04 g/cm^3.   
Volume: 0.96 cm^3/g or 960 cm^3/kg
3.00 mm filament length for 1 kg spool: ~ 130 meters

Following this thinking way, I would make: 93,6m / 12 hours.

Am I missing anything about this math? May I use that density?
Thanks!

]]> Mon, 03 Feb 2014 18:18:20 +0000 https://www.soliforum.com/post/48558/#p48558 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48181/#p48181 K-type.

]]> Wed, 29 Jan 2014 23:56:00 +0000 https://www.soliforum.com/post/48181/#p48181 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48170/#p48170 according to this thread at post #10 --->http://www.soliforum.com/topic/4557/one … d-hotends/ it is a K-type thermocouple.

]]> Wed, 29 Jan 2014 22:54:06 +0000 https://www.soliforum.com/post/48170/#p48170 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48168/#p48168 Tim, could you please tell me what is the thermocouple type? K, T... etc?

Thanks!

]]> Wed, 29 Jan 2014 22:26:07 +0000 https://www.soliforum.com/post/48168/#p48168 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48086/#p48086 Oh.. well... . now I get what is this brass plug!! smile

Excellent! I will let you know of the advances!

Thanks once again!!

]]> Wed, 29 Jan 2014 12:21:40 +0000 https://www.soliforum.com/post/48086/#p48086 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48085/#p48085 henriquesv wrote:

Insert thermocouple in brass plug.

There are only two holes in the brass plug. Plastic comes out of one. The other must be for the thermocouple! Furthermore, you left out part of the instructions. They actually say:

Instructions wrote:

Insert thermocouple in brass plug. Secure with kapton tape, metal zip tie, or pipe clamp (not included)

I do not know how to make that more clear! Insert the thermocouple, secure it with tape.

PID should not be rising 20C beyond set point. Either it needs to be auto tuned, or it is wired incorrectly.

]]> Wed, 29 Jan 2014 12:16:12 +0000 https://www.soliforum.com/post/48085/#p48085 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48083/#p48083 Anyway... a picture of its perfect installation would be really appreciated here.

Thanks!!

]]> Wed, 29 Jan 2014 12:05:26 +0000 https://www.soliforum.com/post/48083/#p48083 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48082/#p48082 PID Temperature is set to 180C, but after some time it is going up to 200C.

Tim, this is what your instructions says this about thermocouple placement (RTA kit –> RTR extruder (electrical)):

"Connect the thermocouple to the controller by sliding it under the screws. Observe polarity. If using
the enclosure, you may need to bend the terminals of the thermocouple so the yellow thermocouple
connector does not interfere with the enclosure. Insert thermocouple in brass plug."

There is no picture nor instructions of its physical installation.

The information regarding the hotend is this:
16.) Wrap hotend with provided insulation. Provided
insulation is a bit intentionally undersized to provide a
tight wrapping. Form it to the shape of the heaterband
by squeezing it around the heater/coupling. Secure with
sticky section of paper wrapping. Edge of insulation
should be

]]> Wed, 29 Jan 2014 11:57:07 +0000 https://www.soliforum.com/post/48082/#p48082 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48081/#p48081 Welp, you put the thermocouple in the wrong place. Please re-read the instructions. What temperature are you using? It should be 180C for ABS.

Motor RPM should be 3-3.5, so that's fine.

What extrusion rate are you seeing? (Inches per minute) you should expect around 4"/min with 3mm filament.

]]> Wed, 29 Jan 2014 11:18:28 +0000 https://www.soliforum.com/post/48081/#p48081 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48078/#p48078 - The heaterband is "facing" the nozzle. So, here's one doubt, should it be closest to the nozzle or it should be on the other side of the part that holds nozzle and barrel together?
- The thermocouple was placed between the heaterband and its holder.
- Nozzle size is 3mm.
- It was extruding really slow... how are you measuring how fas it is? ... I mean.. the pattern that you guys are using? The barrel rotates 1 time / every 15s.

]]> Wed, 29 Jan 2014 09:13:11 +0000 https://www.soliforum.com/post/48078/#p48078 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48050/#p48050 Black seems strange, unless you did a very bad job of cleaning the barrel or are running far too hot.

What temperature is it set to? Where did you put the thermocouple? How fast is it extruding? What nozzle size?

]]> Wed, 29 Jan 2014 00:18:46 +0000 https://www.soliforum.com/post/48050/#p48050 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/48048/#p48048 Hi,
Here's the result after 3 hours extruding. The filament goes from gray to almost black. Does it really take that long to get rid of the rust, contaminants, etc?

I read that it should be running for about 8 hours to be ready for extrusion.

Thanks.

]]> Tue, 28 Jan 2014 23:57:55 +0000 https://www.soliforum.com/post/48048/#p48048 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/47901/#p47901 Yeah! Barrel!
Excellent! Thanks Tim!

]]> Mon, 27 Jan 2014 22:06:12 +0000 https://www.soliforum.com/post/47901/#p47901 <![CDATA[Re: Assemblying my FilaStruder]]> https://www.soliforum.com/post/47900/#p47900 Auger? You mean barrel?

Yeah you should be good to go. They look very similar but that bad batch had a smaller ID. Grind the entrances and deburr it and you should be all set.

]]> Mon, 27 Jan 2014 22:04:31 +0000 https://www.soliforum.com/post/47900/#p47900