<![CDATA[SoliForum - 3D Printing Community — Anyone else have this prob?]]> https://www.soliforum.com/topic/5190/anyone-else-have-this-prob/ Tue, 14 Jan 2014 23:44:41 +0000 PunBB <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46788/#p46788 I know the minute I switched to the E3D 90% of my problems went away.  The other 10% were operator induced.

]]> Tue, 14 Jan 2014 23:44:41 +0000 https://www.soliforum.com/post/46788/#p46788 <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46785/#p46785 I think I lost that a while back with this machine.

]]> Tue, 14 Jan 2014 23:26:26 +0000 https://www.soliforum.com/post/46785/#p46785 <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46783/#p46783 tx-rogue wrote:

thanks

I know it's not the best news but switching will help with your sanity. big_smile

]]> Tue, 14 Jan 2014 23:23:13 +0000 https://www.soliforum.com/post/46783/#p46783 <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46780/#p46780 thanks

]]> Tue, 14 Jan 2014 23:18:53 +0000 https://www.soliforum.com/post/46780/#p46780 <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46774/#p46774 You know that "clogging issue" you think you've worked through....
I am beginning to feel like a broken record.   Buy an E3D from filastruder you'll have it in a couple of days and your problems will end with that.
Otherwise pull the Stock one apart again and re-tighten the barrel to the peek.  (after you clean everything)

]]> Tue, 14 Jan 2014 22:19:58 +0000 https://www.soliforum.com/post/46774/#p46774 <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46773/#p46773 Motor still working. filament just stops.  It is always about 3 hrs which is what has me stumped.

]]> Tue, 14 Jan 2014 22:15:18 +0000 https://www.soliforum.com/post/46773/#p46773 <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46772/#p46772 So when you say "stops extruding" are you saying the extruder motor stops turning or just that filament stops coming out of the hot end?

]]> Tue, 14 Jan 2014 22:13:33 +0000 https://www.soliforum.com/post/46772/#p46772 <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46771/#p46771 Basic info is S2
bed temp 100, 
Extruder temp 200
ABS

]]> Tue, 14 Jan 2014 22:09:40 +0000 https://www.soliforum.com/post/46771/#p46771 <![CDATA[Re: Anyone else have this prob?]]> https://www.soliforum.com/post/46770/#p46770 What temp is your extruder set at?
Sounds to me like some type of clogging or stripped filament.

]]> Tue, 14 Jan 2014 22:06:43 +0000 https://www.soliforum.com/post/46770/#p46770 <![CDATA[Anyone else have this prob?]]> https://www.soliforum.com/post/46769/#p46769 I finally got through the little things like extruder clogging, not sticking, etc., and now have a problem that makes no sense to me.

After printing for about 3 hrs filament stops extruding.  Spool is on a makeshift holder with little tension or resistance.  Tensioner is set adequately, (printed well for 3 hrs +-).  Getting good layers and table adhesion.

Anyone have any ideas??

]]> Tue, 14 Jan 2014 22:00:42 +0000 https://www.soliforum.com/post/46769/#p46769