<![CDATA[SoliForum - 3D Printing Community — FilaWinder Documentation]]> https://www.soliforum.com/topic/5088/filawinder-documentation/ Fri, 10 May 2024 22:08:59 +0000 PunBB <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/155631/#p155631 Here is a new FilaWinder_v13 on Github, programmed by Erich Reich.
Whitout QTR-Sensor calibration needed.
Whitout EEPROM saving (this was limitet on 100000).
Servotypes can changed directly with new ServoValues.
No other Files needed.

https://github.com/erichreich/FilaWinder_V13
FilaWinder_v13.ino

]]> Fri, 10 May 2024 22:08:59 +0000 https://www.soliforum.com/post/155631/#p155631 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/155270/#p155270 Double check you connected everything correctly.
Reflash firmware. Firmware is likely damaged. Happened to me several times.
This thing is bulletproof, should work fine.

]]> Wed, 16 Mar 2022 00:53:12 +0000 https://www.soliforum.com/post/155270/#p155270 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/155269/#p155269 Hi all, I have the trouble of memorize width of swing. Only a certain width is recorded no matter how many times it is set. Does anyone have answer? https://youtu.be/FA64sn4eMHU

]]> Wed, 16 Mar 2022 00:38:42 +0000 https://www.soliforum.com/post/155269/#p155269 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/155060/#p155060 Hi all im trying to make my own filawinder from scrach and cant seem to get the firmware on to an arduino nano but i keep geting an error....
Error compilling for board arduino  nano... any suggestions  on how to fix it

And yes its all plugged in  properly

]]> Sun, 31 Oct 2021 12:45:09 +0000 https://www.soliforum.com/post/155060/#p155060 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/154844/#p154844 How do I reload the firmware? I assume its in the same Arduino app which troubleshooting was done through, right? I got a copy of v11 to load but don't know how to use Arduino well.

]]> Sun, 27 Jun 2021 19:01:07 +0000 https://www.soliforum.com/post/154844/#p154844 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/154843/#p154843 yeah.
I had that too. For what ever reason firmware gets corrupted so i had to reflash it my self at least 2 times in the past.

]]> Sun, 27 Jun 2021 18:46:34 +0000 https://www.soliforum.com/post/154843/#p154843 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/154842/#p154842 tonycstech wrote:

Oh i see. photosensor does not register correctly.
Did you calibrate ?
use piece of filament to calibrate, not a screw driver or anything else.
Clear filament can cause issues but not likely.
Make sure filament is passing at the correct distance from the sensors casting good shadow from the laser.
Laser does work, right ?
And it does point a straight line directly at the sensors right ?
and filament is in between them casting the shadow on the sensors ?
Check the wiring.
I had wiring issues. Pins are cheap, they corrode overtime so spray some alcohol on them, work them in an out couple of times (power disconnected obviously) dry and try again.


Sorry, have to go with the "did you plug it in" method sometimes lol

I did calibrate it and from the screenshot I believe it worked. The loop pos value changes as I move the filament across the photocells which makes me think the calibration, laser, and filament are not the issue. The filament is casting a strong shadow on the photocells. The laser is emitting a strong, straight, red line which lines up directly with the photocells. The wiring matches the instructions. Cleaned the pins with some 91% ISO and the motor still will not turn the spool in auto mode. Could there be an issue with the firmware?

]]> Sun, 27 Jun 2021 16:42:44 +0000 https://www.soliforum.com/post/154842/#p154842 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/154841/#p154841 Oh i see. photosensor does not register correctly.
Did you calibrate ?
use piece of filament to calibrate, not a screw driver or anything else.
Clear filament can cause issues but not likely.
Make sure filament is passing at the correct distance from the sensors casting good shadow from the laser.
Laser does work, right ?
And it does point a straight line directly at the sensors right ?
and filament is in between them casting the shadow on the sensors ?
Check the wiring.
I had wiring issues. Pins are cheap, they corrode overtime so spray some alcohol on them, work them in an out couple of times (power disconnected obviously) dry and try again.


Sorry, have to go with the "did you plug it in" method sometimes lol

]]> Sun, 27 Jun 2021 04:46:05 +0000 https://www.soliforum.com/post/154841/#p154841 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/154840/#p154840 tonycstech wrote:

#1 check the magnet is close enough to the hall sensor.
#2 check the hall sensor following my video tutorial https://www.youtube.com/watch?v=lWezV1Ooa4I

Guide moves when magnet passes by the sensor.
I am not sure if motor has to spin or not at this point.

Consider upgrading to https://www.thingiverse.com/thing:3777364

The hall sensor is working as expected and moving the filament guide when in manual mode. The problem is in auto mode. The filament sensor which tracks the "droop" of the filament as it gets spooled is not triggering the motor to spool the filament. When the reading is above 1500 the motor should turn the spool to bring the filament up so the photocells are sending a value below 1500. The motor which spools the filament never turns on in auto mode.

]]> Sun, 27 Jun 2021 02:36:37 +0000 https://www.soliforum.com/post/154840/#p154840 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/154839/#p154839 #1 check the magnet is close enough to the hall sensor.
#2 check the hall sensor following my video tutorial https://www.youtube.com/watch?v=lWezV1Ooa4I

Guide moves when magnet passes by the sensor.
I am not sure if motor has to spin or not at this point.

Consider upgrading to https://www.thingiverse.com/thing:3777364

]]> Sun, 27 Jun 2021 01:39:27 +0000 https://www.soliforum.com/post/154839/#p154839 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/154838/#p154838 Hello,
I am having difficulty getting my Filawinder to work properly. I believe the issue is with the filament sensor to motor control. I have entered troubling shoot mode and tracked the output. All the inputs are functioning as they should. The filament sensor is feeding the board readings from 0-3000 but the motor will not turn the spool at any point. I attached the Serial Monitor's output showing the sensor data. Is this a software issue? A hardware issue? Any thoughts to a solution are appreciated.
Regards,
Matt
http://soliforum.com/i/?roX0z64.jpg

]]> Sun, 27 Jun 2021 01:26:13 +0000 https://www.soliforum.com/post/154838/#p154838 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/153777/#p153777 chainbreaker2012 wrote:

for the printed parts on main page  I am getting a bad request error. is there another link I could use to download?

Try here https://www.thingiverse.com/thing:174383

]]> Tue, 14 Jul 2020 22:25:39 +0000 https://www.soliforum.com/post/153777/#p153777 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/153776/#p153776 for the printed parts on main page  I am getting a bad request error. is there another link I could use to download?

]]> Tue, 14 Jul 2020 21:57:48 +0000 https://www.soliforum.com/post/153776/#p153776 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/153721/#p153721 Thank you. One last question, I have a bunch of unused STP55NF06L MOSFETs here (replaced from RAMPS boards). Can I use them instead of IRLB8721? Or perhaps IRF1404, which is easier to find here?

]]> Sat, 04 Jul 2020 22:37:36 +0000 https://www.soliforum.com/post/153721/#p153721 <![CDATA[Re: FilaWinder Documentation]]> https://www.soliforum.com/post/153704/#p153704 That would work.   It would look the same to the controller.

]]> Fri, 03 Jul 2020 17:57:39 +0000 https://www.soliforum.com/post/153704/#p153704