<![CDATA[SoliForum - 3D Printing Community — Fluctuating power?]]> https://www.soliforum.com/topic/4892/fluctuating-power/ Fri, 10 Jan 2014 00:41:08 +0000 PunBB <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/46301/#p46301 A problem with "Cheap" PC power supplies is that the 20 amp rating doesn't mean it can sustain that load under normal operating conditions.

]]> Fri, 10 Jan 2014 00:41:08 +0000 https://www.soliforum.com/post/46301/#p46301 <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/46128/#p46128 Thanks for all your input. I haven't had the time to investigate this further.

Other than the flickering LEDs it appears (I emphasise the word appears) to be printing ok. I am just a little concerned.

The output info on the power supply info is on the attached photo, just in case I got something wrong.

]]> Wed, 08 Jan 2014 17:27:41 +0000 https://www.soliforum.com/post/46128/#p46128 <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/44587/#p44587 spapadim wrote:

Perhaps -- I'm no electronics expert. Adrian once suggested he could bore everyone to tears about why LEDs flicker, but unfortunately never elaborated further. smile

FWIW, my clamp meter on my SD2 with everything stock except E3D peaks at about 8A (with stock hotend should be a few amps less, maybe 5?).  Doesn't seem power-starved to me, but it still flickers very noticeably (and it did before the E3D as well).  Also just noting possible alternative explanations: battery could be acting as huge filtering capacitor (esp. if primary source of noise is heater -- perhaps heater coils have nonnegligible inductance? dunno...).

All very possible points maybe we will get lucky and we can get Adrian to chime in and bore us to tears big_smile

]]> Wed, 18 Dec 2013 04:10:01 +0000 https://www.soliforum.com/post/44587/#p44587 <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/44585/#p44585 Perhaps -- I'm no electronics expert. Adrian once suggested he could bore everyone to tears about why LEDs flicker, but unfortunately never elaborated further. smile

FWIW, my clamp meter on my SD2 with everything stock except E3D peaks at about 8A (with stock hotend should be a few amps less, maybe 5?).  Doesn't seem power-starved to me, but it still flickers very noticeably (and it did before the E3D as well).  Also just noting possible alternative explanations: battery could be acting as huge filtering capacitor (esp. if primary source of noise is heater -- perhaps heater coils have nonnegligible inductance? dunno...).

]]> Wed, 18 Dec 2013 04:01:55 +0000 https://www.soliforum.com/post/44585/#p44585 <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/44530/#p44530 spapadim wrote:

LEDs always flicker. Maybe your new heater generates more electrical noise.  I think LED strip is connected straight to 12V without any filtering circuit, so flicker is normal.

Although flickering as very common I wouldn't go so far as to say "Always".  Mine don't flicker and I know a big part of that is from running my bed through a relay and separate power supply in my case AC.  However before I switched to the AC bed I could dramatically decrease my heat up times with a substantial increase in power availability via battery and charger.  As a real positive side effect my LED's no longer flickered.
If you are starving your LED's for power just imagine what everything else in your system is up against.  I have found that the whole printer just works better with adequate power.

]]> Tue, 17 Dec 2013 18:00:31 +0000 https://www.soliforum.com/post/44530/#p44530 <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/44528/#p44528 LEDs always flicker. Maybe your new heater generates more electrical noise.  I think LED strip is connected straight to 12V without any filtering circuit, so flicker is normal.

]]> Tue, 17 Dec 2013 17:48:57 +0000 https://www.soliforum.com/post/44528/#p44528 <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/44523/#p44523 satman49 wrote:

How about using a 12v car battery?  I use that on my Arduino project.

Yep that will work but you car wont run as well big_smile.
I actually ran a charger on a smaller ATV battery as a bit of a sink to keep the voltage in line.

]]> Tue, 17 Dec 2013 16:42:12 +0000 https://www.soliforum.com/post/44523/#p44523 <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/44522/#p44522 How about using a 12v car battery?  I use that on my Arduino project.

]]> Tue, 17 Dec 2013 16:40:19 +0000 https://www.soliforum.com/post/44522/#p44522 <![CDATA[Re: Fluctuating power?]]> https://www.soliforum.com/post/44515/#p44515 It does sound like you have a shortage of available power.  If your power supply can only deliver 240 watts maximum I would figure out the wattage of your bed heater.  Grab another power supply to test with.  I have run my printer with a battery charger as a test.  It worked fine when I ran it on the 50 Amp setting.  Make sure if you do this that the charger isn't putting out much more than 14 volts.  This should just be a test, I have run several hours with this setup when my printer showed up with a bad power supply but I wouldn't recommend it.

]]> Tue, 17 Dec 2013 15:38:43 +0000 https://www.soliforum.com/post/44515/#p44515 <![CDATA[Fluctuating power?]]> https://www.soliforum.com/post/44505/#p44505 When printing I have noticed that the lights on my SD3 fluctuate in brightness as the bed or hot end is heated. This would indicate that the printer isn't getting enough power right?

I recently replaced the heat pad (as mine had burnt out) along with the power supply, and thicker wiring as required, following the post on here about replacing the heat pad (including soldering on the jumper cables for the MOSFET).

The power supply I used is a cheap 500w PC power supply I had spare. I checked the ratings of it and the 12v supply gives out a maximum of 20A.

The new heated bed gets up to temperature in about 20 to 30 mins. It's one like this (can't find the actual listing for mine) http://www.emakershop.com/browse/listing?l=725

Any ideas?

]]> Tue, 17 Dec 2013 12:55:41 +0000 https://www.soliforum.com/post/44505/#p44505