<![CDATA[SoliForum - 3D Printing Community — Thickening Walls To Make Printable???]]> https://www.soliforum.com/topic/4671/thickening-walls-to-make-printable/ Sat, 30 Nov 2013 05:16:48 +0000 PunBB <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42887/#p42887 Serin wrote:

Can't you simply attach it to a post here?

Lawsy is the one who volunteered. I don't want to give my work thus far out to the general public just because. lol.

]]> Sat, 30 Nov 2013 05:16:48 +0000 https://www.soliforum.com/post/42887/#p42887 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42878/#p42878 Strange.  I know that I'm practically dreaming because the only problem I had with the printer was that I had to thicken everything or it wouldn't print.  Oh well, maybe he'll try it now that two people suggested? lol

]]> Sat, 30 Nov 2013 03:47:17 +0000 https://www.soliforum.com/post/42878/#p42878 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42851/#p42851 I did make a similar suggestion re 1.0RC1 and it's thin wall detection few days ago.. but based on the replies or lack there of I'm assuming it didn't seem to suit. .*shrug*. ..

]]> Fri, 29 Nov 2013 22:39:58 +0000 https://www.soliforum.com/post/42851/#p42851 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42849/#p42849 On the new 1.0RC version of slic3r I can have 1/32" walls and it still works properly.  Until this point, on 0.9whatever, if I went under 1/8" it would fail with the two parallel lines.

]]> Fri, 29 Nov 2013 22:25:47 +0000 https://www.soliforum.com/post/42849/#p42849 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42819/#p42819 Can't you simply attach it to a post here?

]]> Fri, 29 Nov 2013 06:46:08 +0000 https://www.soliforum.com/post/42819/#p42819 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42818/#p42818 lawsy wrote:

I've never heard of it. Just make sure I don't have to make an account to download it.

It seems to require your e-mail so it can message you directly. Prefer a different site?

]]> Fri, 29 Nov 2013 05:22:22 +0000 https://www.soliforum.com/post/42818/#p42818 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42815/#p42815 I've never heard of it. Just make sure I don't have to make an account to download it.

]]> Fri, 29 Nov 2013 05:11:37 +0000 https://www.soliforum.com/post/42815/#p42815 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42808/#p42808 lawsy wrote:

Can you link to the file so I can have a go?

Sure. Is https://www.wetransfer.com/ a good service to use?

]]> Fri, 29 Nov 2013 02:37:02 +0000 https://www.soliforum.com/post/42808/#p42808 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42637/#p42637 Can you link to the file so I can have a go?

]]> Tue, 26 Nov 2013 20:24:22 +0000 https://www.soliforum.com/post/42637/#p42637 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42635/#p42635 lawsy wrote:

Did you see the bit at the end where they joined the two surfaces back up?

I followed everything he did but they stayed seperate. I made it using Autodesk 123D Catch so the model might a bit holely. Not sure if that is the issue. I am currently trying to adjust the flow of my extrusions as it was taking in 13cm of ABS for every 10cm it said it was so I changed the stepper motor rate. I am currently trying to find the best extrusion multiplier because whenever I used higher infills before it made the outside of models bumpy and ugly looking.

]]> Tue, 26 Nov 2013 20:13:37 +0000 https://www.soliforum.com/post/42635/#p42635 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42597/#p42597 Did you see the bit at the end where they joined the two surfaces back up?

]]> Tue, 26 Nov 2013 07:00:43 +0000 https://www.soliforum.com/post/42597/#p42597 <![CDATA[Re: Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42595/#p42595 grab the new slic3r from slic3r.org, 1.0RC1 . It has an option 'detect thin walls' which works better on thin walls in general. And then ramp up your infill ?

]]> Tue, 26 Nov 2013 06:15:49 +0000 https://www.soliforum.com/post/42595/#p42595 <![CDATA[Thickening Walls To Make Printable???]]> https://www.soliforum.com/post/42594/#p42594 http://www.youtube.com/watch?v=ILKspBZjSDM

I tried this method, but really just ended up with two parallel surfaces that I can't close up at the seams. Any other suggestions or does anyone want to make an attempt at it for me?

]]> Tue, 26 Nov 2013 06:12:13 +0000 https://www.soliforum.com/post/42594/#p42594