<![CDATA[SoliForum - 3D Printing Community — Elf test]]> https://www.soliforum.com/topic/4664/elf-test/ Wed, 18 Dec 2013 00:20:28 +0000 PunBB <![CDATA[Re: Elf test]]> https://www.soliforum.com/post/44571/#p44571 that is a very nice print. unfortunate about the glass. Im sure i have enough picture frames to last a while before i move to the ebay store smile

]]> Wed, 18 Dec 2013 00:20:28 +0000 https://www.soliforum.com/post/44571/#p44571 <![CDATA[Re: Elf test]]> https://www.soliforum.com/post/42560/#p42560 Wow, I've been using 1/16" or 2mm thick glass for months, hundreds of prints, no problems!! It must be the warped printbed...

Then again I only use PLA, and heat my bed to 65°.... I guess thats Y mine held up!!

Stevos758 wrote:

By those black binder clips. It broke while cooling. Thin 1/8" glass. I think my heatbed is a little uneven flexing the glass when clipped down Going to pick up some 1/4" today.

]]> Mon, 25 Nov 2013 21:07:21 +0000 https://www.soliforum.com/post/42560/#p42560 <![CDATA[Re: Elf test]]> https://www.soliforum.com/post/42557/#p42557 Stevos758 wrote:

This little pecker broke my glass.

http://i.imgur.com/sEfrBPr.jpg

This is why I keep telling people - Borosillicate (aka Pyrex) is what you are supposed to use! smile Normal glass will do this again and again due to thermal stress - its not designed for heat cycles no matter how cheap it is or which walmart it comes from wink smile

Just order a piece from the hundreds of 3d'ers on ebay that sell them for $10 and you'll never buy another piece of glass again wink

Nice print though! smile

]]> Mon, 25 Nov 2013 21:00:35 +0000 https://www.soliforum.com/post/42557/#p42557 <![CDATA[Re: Elf test]]> https://www.soliforum.com/post/42553/#p42553 By those black binder clips. It broke while cooling. Thin 1/8" glass. I think my heatbed is a little uneven flexing the glass when clipped down Going to pick up some 1/4" today.

]]> Mon, 25 Nov 2013 20:46:54 +0000 https://www.soliforum.com/post/42553/#p42553 <![CDATA[Re: Elf test]]> https://www.soliforum.com/post/42545/#p42545 Hi, nice elf, how was your glass held in place?

]]> Mon, 25 Nov 2013 19:56:22 +0000 https://www.soliforum.com/post/42545/#p42545 <![CDATA[Re: Elf test]]> https://www.soliforum.com/post/42540/#p42540 scary.

]]> Mon, 25 Nov 2013 18:31:30 +0000 https://www.soliforum.com/post/42540/#p42540 <![CDATA[Re: Elf test]]> https://www.soliforum.com/post/42536/#p42536 Bad Elf!!!


When did he break it? while printing or afterwards

]]> Mon, 25 Nov 2013 17:59:25 +0000 https://www.soliforum.com/post/42536/#p42536 <![CDATA[Elf test]]> https://www.soliforum.com/post/42533/#p42533 This little pecker broke my glass.

http://i.imgur.com/sEfrBPr.jpg

]]> Mon, 25 Nov 2013 17:31:35 +0000 https://www.soliforum.com/post/42533/#p42533