<![CDATA[SoliForum - 3D Printing Community — suport material]]> https://www.soliforum.com/topic/4503/suport-material/ Sun, 16 Feb 2014 11:21:55 +0000 PunBB <![CDATA[Re: suport material]]> https://www.soliforum.com/post/49899/#p49899 If you calibrate the extruder, adjust the bed and enter these settings, you should get good prints. At least I did. I had to lower infill extrusion width to .4 and set flow rate to 0.95 and it is all good!

]]> Sun, 16 Feb 2014 11:21:55 +0000 https://www.soliforum.com/post/49899/#p49899 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/49858/#p49858 i have kiss slicer downloaded and intergrated to Rhost i just cant get my head around those settings its all screwy to me after Slic3r..

ill give it another try

]]> Sun, 16 Feb 2014 00:28:29 +0000 https://www.soliforum.com/post/49858/#p49858 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/49806/#p49806 Thank you so much for these settings! The printer is printing flawlessly now!

The problem was the setting for firmware: 5D Relative E and Absolute E. I set it to absolute E and the extruder jumping stopped.

]]> Sat, 15 Feb 2014 13:05:42 +0000 https://www.soliforum.com/post/49806/#p49806 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/42002/#p42002 never mind fixed the problem

]]> Wed, 20 Nov 2013 03:14:56 +0000 https://www.soliforum.com/post/42002/#p42002 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/42001/#p42001 im calibrating the flow rate now,
printing a test box, that has an open top

after it does its two bottom layers it does about 6 perimeter layers then after that, it goes to infill again,
my box was created 40x40x40 mm hollow with a 3 mm wall thickness.

any ideas?

]]> Wed, 20 Nov 2013 02:57:56 +0000 https://www.soliforum.com/post/42001/#p42001 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41525/#p41525 The extruder stepper calibration is only for RH.

The flow rate calibration can be done in slic3r/RH and then use that number in the flow tweak of Kisslicer. This flow rate calibration should be done with every different roll of ABS/PLA you put on because each roll will have its own difference.

]]> Wed, 13 Nov 2013 02:13:22 +0000 https://www.soliforum.com/post/41525/#p41525 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41523/#p41523 then I wont have to modify that part for kisslicer again correct?

just the filament extrusion.

]]> Wed, 13 Nov 2013 01:52:47 +0000 https://www.soliforum.com/post/41523/#p41523 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41518/#p41518 yup. measure the difference. calculate the percentage its off. multiply times what the current number is in EEPROM. Enter new number. Save. Then test again.

]]> Wed, 13 Nov 2013 01:12:08 +0000 https://www.soliforum.com/post/41518/#p41518 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41517/#p41517 muddtt wrote:

Should do calibration of extruder stepper first. Then flow rate. Theres a menu in RH now for eeprom settings that make it easier to change the numbers.

I don't have to do anything special with the reset button on repetier right?
I can just measure the filament and how much its using and compare to the what it should.
change the numbers to what they need to be and save to EEPROM right?

]]> Wed, 13 Nov 2013 01:08:29 +0000 https://www.soliforum.com/post/41517/#p41517 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41465/#p41465 Should do calibration of extruder stepper first. Then flow rate. Theres a menu in RH now for eeprom settings that make it easier to change the numbers.

]]> Tue, 12 Nov 2013 15:17:12 +0000 https://www.soliforum.com/post/41465/#p41465 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41445/#p41445 muddtt wrote:

Filament settings tab. You should have calibrated this once upon a time

http://www.soliwiki.com/Calibration_of_the_flow_rate
And
http://www.soliwiki.com/Calibration_of_ … on_stepper
Are both very important.

yeah I never did that,
uh oh,
probably could get some even more amazing print quality if I did this huh?

]]> Tue, 12 Nov 2013 10:15:53 +0000 https://www.soliforum.com/post/41445/#p41445 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41442/#p41442 Filament settings tab. You should have calibrated this once upon a time

http://www.soliwiki.com/Calibration_of_the_flow_rate
And
http://www.soliwiki.com/Calibration_of_ … on_stepper
Are both very important.

]]> Tue, 12 Nov 2013 06:01:45 +0000 https://www.soliforum.com/post/41442/#p41442 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41441/#p41441 found it.

]]> Tue, 12 Nov 2013 06:01:02 +0000 https://www.soliforum.com/post/41441/#p41441 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41439/#p41439 muddtt wrote:

Well first things i'd input would be your filament diameter. Then "flow tweak" would be your extrusion multiplier in slic3r.

And yes, the speed tweaks are controlled in the speed tab

where in slic3r would I fine the "extrusion multiplier"? just so I know im printing about the same as I was with slic3r, because kisslicer is looking kinda weak, and is stringy kinda.

]]> Tue, 12 Nov 2013 05:53:19 +0000 https://www.soliforum.com/post/41439/#p41439 <![CDATA[Re: suport material]]> https://www.soliforum.com/post/41437/#p41437 Well first things i'd input would be your filament diameter. Then "flow tweak" would be your extrusion multiplier in slic3r.

And yes, the speed tweaks are controlled in the speed tab

]]> Tue, 12 Nov 2013 05:49:10 +0000 https://www.soliforum.com/post/41437/#p41437