<![CDATA[SoliForum - 3D Printing Community — Glass bed No Stick]]> https://www.soliforum.com/topic/440/glass-bed-no-stick/ Wed, 26 Jun 2013 21:07:05 +0000 PunBB <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/28113/#p28113 assuming you have the correct thermistor table selected, try printing at 175C

]]> Wed, 26 Jun 2013 21:07:05 +0000 https://www.soliforum.com/post/28113/#p28113 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/27440/#p27440 Blue painters tape or hairspray, or ABS Slurry (ABS Melted into acetone)

]]> Fri, 21 Jun 2013 22:44:13 +0000 https://www.soliforum.com/post/27440/#p27440 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/26664/#p26664 Maybe some hairspray could help !

]]> Mon, 17 Jun 2013 10:37:34 +0000 https://www.soliforum.com/post/26664/#p26664 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/26656/#p26656 I couldn't get PLA to glass unless I set the bed temp to at least that of ABS bed temp.

With zero temperature the PLA sticks nicely to 3M blue tape.

]]> Mon, 17 Jun 2013 09:02:56 +0000 https://www.soliforum.com/post/26656/#p26656 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/26654/#p26654 Before the next print wipe the surface with a disolvent, acetona.

]]> Mon, 17 Jun 2013 08:45:13 +0000 https://www.soliforum.com/post/26654/#p26654 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/3980/#p3980 I etched the glass top surface with etching cream.

PLA still won't stick    Extruder temp  200 / 185      Bed   75 / 25

Any help?

Tnx
Ray

]]> Fri, 02 Nov 2012 23:19:33 +0000 https://www.soliforum.com/post/3980/#p3980 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/3828/#p3828 The ABS is good, but PLA can be a different matter.  Those who are trying it say that once you get it stuck, it works great, and the reduced cost is worth the effort to get it dialed in.

]]> Thu, 01 Nov 2012 18:50:10 +0000 https://www.soliforum.com/post/3828/#p3828 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/3817/#p3817 Same with me.
Still using factory Kapton tape on bed and Solidoodle and Octave abs.
And every once in a while I have had to realign my table height after trying to remove super stuck prints even after the bed has cooled down.

]]> Thu, 01 Nov 2012 18:40:32 +0000 https://www.soliforum.com/post/3817/#p3817 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/3810/#p3810 After having some issues with my Octave ABS at first, I've got it dialed in to where I'm having a hard time taking it off the build platform now.  Still using factory Kapton tape with rips in it and all.

]]> Thu, 01 Nov 2012 18:33:46 +0000 https://www.soliforum.com/post/3810/#p3810 <![CDATA[Re: Glass bed No Stick]]> https://www.soliforum.com/post/3806/#p3806 What PLA are you using?  Chinese PLA from the likes of RepRaper, Octave, etc have a reputation for being difficult to stick.

]]> Thu, 01 Nov 2012 18:29:45 +0000 https://www.soliforum.com/post/3806/#p3806 <![CDATA[Glass bed No Stick]]> https://www.soliforum.com/post/3792/#p3792 PLA NOT sticking to glass bed

I installed a glass bed on my Ordbot Hadron
Common window glass over heated aluminum bed
using PLA at Extruder temp  185 - 200
bed temps 40 - 90

Glass cleaned with ammonia cleaner
Bare glass tried   hair spray on glass tried

First layer being smooshed into bed

Extruded plastic isn't sticking at all

any suggestions?

tnx
Ray

]]> Thu, 01 Nov 2012 17:43:19 +0000 https://www.soliforum.com/post/3792/#p3792