<![CDATA[SoliForum - 3D Printing Community — Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/topic/3767/extruder-heater-shutting-off-after-every-print-why/ Mon, 02 Sep 2013 19:30:47 +0000 PunBB <![CDATA[Re: Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/post/35007/#p35007 I run M104 S130 in my end g-code. I don't have any problems either.

]]> Mon, 02 Sep 2013 19:30:47 +0000 https://www.soliforum.com/post/35007/#p35007 <![CDATA[Re: Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/post/34994/#p34994 TheBaron wrote:

Personally, I like disabling the print head between jobs because it helps avoid having filament sitting hot in there. Seems to be the leading cause of clogs.

+1 on that...I never leave my extruder hot without running a print; and it heats up so fast, I find it a non-issue.  BTW, I've haven't had a clog in over a year.

]]> Mon, 02 Sep 2013 17:22:00 +0000 https://www.soliforum.com/post/34994/#p34994 <![CDATA[Re: Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/post/34992/#p34992 Personally, I like disabling the print head between jobs because it helps avoid having filament sitting hot in there. Seems to be the leading cause of clogs.

]]> Mon, 02 Sep 2013 16:36:10 +0000 https://www.soliforum.com/post/34992/#p34992 <![CDATA[Re: Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/post/34927/#p34927 That was it R2. Thanks!

]]> Mon, 02 Sep 2013 01:32:35 +0000 https://www.soliforum.com/post/34927/#p34927 <![CDATA[Re: Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/post/34926/#p34926 Hearthlander, I'm no where near my computer but in rh under printer settings there is an option to disable heaters after job/kill

]]> Mon, 02 Sep 2013 01:29:09 +0000 https://www.soliforum.com/post/34926/#p34926 <![CDATA[Re: Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/post/34923/#p34923 Okay, thanks. Not being a G Coder, I assume you mean there is a M104 SO in the GCode. So, how to I make it stop doing that? Also, could you recommend a good primer on GCode? Thanks, Ian.

]]> Mon, 02 Sep 2013 01:01:40 +0000 https://www.soliforum.com/post/34923/#p34923 <![CDATA[Re: Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/post/34921/#p34921 M104 S0  in the end gcode

]]> Mon, 02 Sep 2013 00:51:15 +0000 https://www.soliforum.com/post/34921/#p34921 <![CDATA[Extruder heater shutting off after every print. Why?]]> https://www.soliforum.com/post/34919/#p34919 Using Repetier and Slic3r. I think I must have set an option somewhere to tell it to do this since it does it so infallibly, but where? I'd rather it stayed on.

]]> Mon, 02 Sep 2013 00:41:42 +0000 https://www.soliforum.com/post/34919/#p34919