<![CDATA[SoliForum - 3D Printing Community — Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/topic/3586/updated-firmware-now-i-have-z-wobble-update-92013/ Sat, 21 Sep 2013 01:41:23 +0000 PunBB <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/36929/#p36929 Yes mine is just above not extruding. I have a m5 rod and m8 for replacement caridge. Should be here early next week. The new stepper is awesome. I hope the m5 cleans up the rest.

]]> Sat, 21 Sep 2013 01:41:23 +0000 https://www.soliforum.com/post/36929/#p36929 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/36920/#p36920 looks okay to me. Time to replace the 5/16" threaded rod though.

]]> Fri, 20 Sep 2013 22:49:29 +0000 https://www.soliforum.com/post/36920/#p36920 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/36918/#p36918 Did you tune your VREF?

I had to turn mine way down; to just above where extrusion stopped.

]]> Fri, 20 Sep 2013 22:32:24 +0000 https://www.soliforum.com/post/36918/#p36918 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/36917/#p36917 Here are some pics after the stepper was installed.

]]> Fri, 20 Sep 2013 22:16:04 +0000 https://www.soliforum.com/post/36917/#p36917 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/36913/#p36913 Stepper installed. Looks much better. Something is still going on. I'll get a pic up when my print is done.

]]> Fri, 20 Sep 2013 21:43:25 +0000 https://www.soliforum.com/post/36913/#p36913 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/36706/#p36706 Ordered the Pololu 1/32 driver. I'll report back when I have it installed.

]]> Wed, 18 Sep 2013 12:23:16 +0000 https://www.soliforum.com/post/36706/#p36706 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/36480/#p36480 I have some parts I will get pics of. I messed with the stepper Pot. I need to upgrade. I couldn't get it to go away. I'll get some pics up.

I ran a print and tried to adjust on the fly. I turned it down untill it started skipping and went up ever so slightly. It looks a little better but not gone. I am almost back to where I started.

Are the stepper drivers drop in besides changing the firmware? What do you recommend?

]]> Mon, 16 Sep 2013 13:36:38 +0000 https://www.soliforum.com/post/36480/#p36480 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/33817/#p33817 Try printing some calibration pieces that are vertical and see that you get.

]]> Wed, 21 Aug 2013 18:18:33 +0000 https://www.soliforum.com/post/33817/#p33817 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/33814/#p33814 I will have to try this still. Haven't had time.

What about the slight banding. I am going to pick up an M5 rod which hopefully will help.

]]> Wed, 21 Aug 2013 18:01:26 +0000 https://www.soliforum.com/post/33814/#p33814 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/33813/#p33813 you should look at this thread I made about a week ago on uneven microstepping

http://www.soliforum.com/topic/3491/ext … g-to-fail/

I did only start to notice it when I went to the E3D

]]> Wed, 21 Aug 2013 17:54:58 +0000 https://www.soliforum.com/post/33813/#p33813 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/33522/#p33522 I haven't got around to this yet. What exactly does this trim pot do? Does it adjust speed or power? Is this on the motor itself or on the board?

]]> Mon, 19 Aug 2013 13:28:45 +0000 https://www.soliforum.com/post/33522/#p33522 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/33344/#p33344 the filament might be a have a little more resistance with the E3D since it is stainless and not PEEK lined with teflon. that is my guess. I had the same thing with my E3D.

]]> Sat, 17 Aug 2013 22:32:04 +0000 https://www.soliforum.com/post/33344/#p33344 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/33336/#p33336 I will give it a try. Any Idea of what would have caused this? It was working perfect before I put the E3D on?

]]> Sat, 17 Aug 2013 21:54:27 +0000 https://www.soliforum.com/post/33336/#p33336 <![CDATA[Re: Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/33331/#p33331 that doesn't look like z-wobble. That looks like moire from the extruder. Try backing the trimpot on your extruder stepper driver counter clockwise a 1/16-1/32 of a turn.

Other methods for setting extruder trim pot -

[*]set to 0 - full counter clockwise (careful not to go past stop)[/*]
[*]in RH set manual extrude speed to 5mm/s[/*]
[*]extrude 100mm [/*]
[*]slowly adjust the trimpot clockwise (1/16 of a turn at a time) until you hear the extruder start extruding smoothly[/*]

]]> Sat, 17 Aug 2013 21:20:03 +0000 https://www.soliforum.com/post/33331/#p33331 <![CDATA[Updated firmware. Now I have Z wobble. Update! 9-20-13]]> https://www.soliforum.com/post/33329/#p33329 I installed my e3d and had to update the firmware for the E3D temps. Now i have developed some Z- wobble.
How do I get rid of this using the firmware. My prints were fine before.

]]> Sat, 17 Aug 2013 20:49:30 +0000 https://www.soliforum.com/post/33329/#p33329