<![CDATA[SoliForum - 3D Printing Community — Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/topic/3564/anyone-making-a-heat-box-to-store-filament/ Sat, 17 Aug 2013 09:10:49 +0000 PunBB <![CDATA[Re: Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/post/33294/#p33294 This is intended for water soluble filament but you could probably incorporate it, or components of it.

http://www.thingiverse.com/thing:72304

]]> Sat, 17 Aug 2013 09:10:49 +0000 https://www.soliforum.com/post/33294/#p33294 <![CDATA[Re: Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/post/33162/#p33162 i have a 60w light bulb in a 52L plastic storage box with 2 kg of rice in the bottom and i still have moist filament damn living too close to Antarctica sucks.

the box stays at a constant 25 degrees C

do you think the dehumidifier rod would be up to that task? if so can you get them in 240v versions?

]]> Fri, 16 Aug 2013 10:13:04 +0000 https://www.soliforum.com/post/33162/#p33162 <![CDATA[Re: Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/post/33094/#p33094 I have a ton of space under the desk.... The gears are a turning.

]]> Thu, 15 Aug 2013 18:50:48 +0000 https://www.soliforum.com/post/33094/#p33094 <![CDATA[Re: Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/post/33085/#p33085 You might like something like this - http://www.thingiverse.com/thing:34300

It's a guide for running filament from a bunch of spools set up under the desk.

]]> Thu, 15 Aug 2013 17:40:54 +0000 https://www.soliforum.com/post/33085/#p33085 <![CDATA[Re: Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/post/33064/#p33064 I have had plans for the last six months to get around making a little arduino controlled unit... They have a lot of humidity sensors that could turn the heaters on and off in the box depending on humidity. Then feeding the filament through a piece of styrofoam,  we could have it go direct to the solidoodle.  But it's always on the bottom of my task list hmm

]]> Thu, 15 Aug 2013 14:36:35 +0000 https://www.soliforum.com/post/33064/#p33064 <![CDATA[Re: Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/post/33059/#p33059 That looks like it will work pretty good. I suppose I could just do my initial dry in the oven and store the filament in something like that.

]]> Thu, 15 Aug 2013 14:07:50 +0000 https://www.soliforum.com/post/33059/#p33059 <![CDATA[Re: Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/post/33058/#p33058 Search for "golden rod" . I have a big Tupperware container that I keep my filament with the golden rod. it keeps it dry and might work for what you were thinking.

]]> Thu, 15 Aug 2013 14:05:05 +0000 https://www.soliforum.com/post/33058/#p33058 <![CDATA[Anyone making a "Heat Box" to store filament?]]> https://www.soliforum.com/post/33057/#p33057 I had a vision today of making a heated box behind my Doodle with shelves and a pipe to feed my filament into the doodle.

Basically i would have several shelves to store spare filaments and have a station with a large spool and small spool holder to feed filament through a hole in the front.

The only reason I am thinking of doing this is I have some nylon on the way and I have heard of problems printing with moist nylon.

What do you think I should consider for the heating element?

I'll post a sketch up when I get time.

]]> Thu, 15 Aug 2013 13:48:31 +0000 https://www.soliforum.com/post/33057/#p33057