<![CDATA[SoliForum - 3D Printing Community — SD3 Bed heater failure]]> https://www.soliforum.com/topic/3502/sd3-bed-heater-failure/ Mon, 19 Aug 2013 17:48:14 +0000 PunBB <![CDATA[Re: SD3 Bed heater failure]]> https://www.soliforum.com/post/33558/#p33558 Thanks, I thought it might be an email error of some kind.

]]> Mon, 19 Aug 2013 17:48:14 +0000 https://www.soliforum.com/post/33558/#p33558 <![CDATA[Re: SD3 Bed heater failure]]> https://www.soliforum.com/post/33538/#p33538 Kerry wrote:

I'm up to support request email number 6 without response from Solidoodle.
If anyone at the company is looking at this would you check the support@solidoodle.com mail account.

We don't have any e-mails from you as of now. We're having a CSR e-mail you from the e-mail address listed on your order.

]]> Mon, 19 Aug 2013 15:15:20 +0000 https://www.soliforum.com/post/33538/#p33538 <![CDATA[Re: SD3 Bed heater failure]]> https://www.soliforum.com/post/33531/#p33531 I'm up to support request email number 6 without response from Solidoodle.
If anyone at the company is looking at this would you check the support@solidoodle.com mail account.

]]> Mon, 19 Aug 2013 14:31:58 +0000 https://www.soliforum.com/post/33531/#p33531 <![CDATA[Re: SD3 Bed heater failure]]> https://www.soliforum.com/post/33486/#p33486 I don't know what was wrong, but I just had my bed temp drop out as well.  I usually run the bed temp at 98... it was down to 38.  I've been printing pretty steady since the beginning of July with 0 problems.  I was just looking at the back of  machine, I blew on it, and the bed started to heat up again.  Should I put a fan on the back?

]]> Mon, 19 Aug 2013 04:58:38 +0000 https://www.soliforum.com/post/33486/#p33486 <![CDATA[Re: SD3 Bed heater failure]]> https://www.soliforum.com/post/32423/#p32423 Thanks,
I have sent 4 messages over 9 days to support@solidoodle.com without response.
let me know if I have the wrong address.

]]> Fri, 09 Aug 2013 17:48:13 +0000 https://www.soliforum.com/post/32423/#p32423 <![CDATA[Re: SD3 Bed heater failure]]> https://www.soliforum.com/post/32417/#p32417 Send a email message to support. Sounds like your bed is blown.

]]> Fri, 09 Aug 2013 16:28:19 +0000 https://www.soliforum.com/post/32417/#p32417 <![CDATA[SD3 Bed heater failure]]> https://www.soliforum.com/post/32415/#p32415 Hi All,
My new SD3 bed heater stopped working and I was looking for some help.
I have never had the temperature of the bed set over 85c and have gone through
approx. 1/4th of a 2lb spool of ABS.
After a quick look, the bed resistor is at 53.2kohms and I do get 12vdc (unloaded) out of the
controller. my guess is the resistor or heater is bad and would only produce 2.71mwatts of power at 12vdc.
Thanks in advance for any help.

]]> Fri, 09 Aug 2013 16:00:53 +0000 https://www.soliforum.com/post/32415/#p32415