<![CDATA[SoliForum - 3D Printing Community — X Axis Slant after 10mm or so]]> https://www.soliforum.com/topic/3478/x-axis-slant-after-10mm-or-so/ Mon, 19 Aug 2013 17:23:11 +0000 PunBB <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/33553/#p33553 I needed to print something quickly and turned the left rod a little bit (randomly).

The slant is seems to be much less severe now, so it looks like this is the right path to go down. Gonna do some calibration shapes when I can and see if I can't reduce it even less.

I'll post back with results when I've got them.

Thanks for the help, guys smile

]]> Mon, 19 Aug 2013 17:23:11 +0000 https://www.soliforum.com/post/33553/#p33553 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/33455/#p33455 It also might explain the creaking sound I get when I home the Z axis.

I haven't had a chance to play around with it yet, but I'll post back as soon as I have.

]]> Sun, 18 Aug 2013 23:22:54 +0000 https://www.soliforum.com/post/33455/#p33455 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/33441/#p33441 I'm with ronsii on this one, bent z rod? Should almost be able to see this much wobble.

]]> Sun, 18 Aug 2013 19:17:09 +0000 https://www.soliforum.com/post/33441/#p33441 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32913/#p32913 Also mark the rods with a sharpie on the end so you can keep track of their orientation and also see if they may be moving/rotating as the bed moves.

]]> Wed, 14 Aug 2013 14:09:18 +0000 https://www.soliforum.com/post/32913/#p32913 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32912/#p32912 I'll give that a go, thanks.

]]> Wed, 14 Aug 2013 14:08:56 +0000 https://www.soliforum.com/post/32912/#p32912 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32911/#p32911 With a slant in the same spot/length/direction every time I would suspect that something is bent or otherwise not straight... have you tried rotating the z rods either one at a time or both together about their z-axis 90 or 180 degrees... might help if not it eliminates one possible cause smile

]]> Wed, 14 Aug 2013 14:07:33 +0000 https://www.soliforum.com/post/32911/#p32911 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32874/#p32874 Everything I print suffers the same slant at the same height.

Support suggested a fan on the board, but that didn't change anything when I tried.

]]> Wed, 14 Aug 2013 09:38:40 +0000 https://www.soliforum.com/post/32874/#p32874 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32848/#p32848 Probably not IMO. You have a fan on your controller? Also, what happens if you print something else? Can you find something on thingiverse and print it? Might help to narrow down the issue.

]]> Wed, 14 Aug 2013 01:49:19 +0000 https://www.soliforum.com/post/32848/#p32848 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32800/#p32800 Loosening the screws holding the wooden block that contains the Z-Axis nut has helped somewhat, but not completely.

Could it be the Z rod isn't straight and is moving the bed?

]]> Tue, 13 Aug 2013 16:14:09 +0000 https://www.soliforum.com/post/32800/#p32800 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32792/#p32792 No change, unfortunately.

]]> Tue, 13 Aug 2013 14:32:03 +0000 https://www.soliforum.com/post/32792/#p32792 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32789/#p32789 Thanks. I've adjusted the blocks (just in case) and will run a print now, then post back with the results.

]]> Tue, 13 Aug 2013 14:01:37 +0000 https://www.soliforum.com/post/32789/#p32789 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32784/#p32784 but since your slant comes and goes I don't think this will cure it....

]]> Tue, 13 Aug 2013 13:50:13 +0000 https://www.soliforum.com/post/32784/#p32784 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32782/#p32782 The perpendicularness of the Z to X can be controlled by adjusting the white bearing blocks on the right end of the Y carriage, adjust the top one to set the angle then bring the bottom one up until just about touching the rod... check full travel of the rod for binding once set.

]]> Tue, 13 Aug 2013 13:49:29 +0000 https://www.soliforum.com/post/32782/#p32782 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32777/#p32777 Would this explain the type of slant I'm seeing? The first layers are perfect and after the slant the layers are perfectly aligned. It's just a section of about 10mm that experiences the slant.

If the rods aren't already perpendicular, is that something I can even fix? The holes for the rods are built into the frame.

]]> Tue, 13 Aug 2013 13:24:22 +0000 https://www.soliforum.com/post/32777/#p32777 <![CDATA[Re: X Axis Slant after 10mm or so]]> https://www.soliforum.com/post/32774/#p32774 Perhaps your x rods need to be perpendicular to your z rods. Easier said than done. Then bed needs to be on same plane as nozzle. In that order. May need to get creative with your adjustments.

]]> Tue, 13 Aug 2013 13:17:27 +0000 https://www.soliforum.com/post/32774/#p32774