<![CDATA[SoliForum - 3D Printing Community — J-Head not heating.]]> https://www.soliforum.com/topic/3183/jhead-not-heating/ Sun, 21 Jul 2013 07:54:14 +0000 PunBB <![CDATA[Re: J-Head not heating.]]> https://www.soliforum.com/post/30485/#p30485 And its fixed!

http://www.pdxmc.com/uploads/SD3/20130721_004949.jpg

That is a twisted vase of my own design, I will get it and some others posted up on thingiverse soon.

]]> Sun, 21 Jul 2013 07:54:14 +0000 https://www.soliforum.com/post/30485/#p30485 <![CDATA[Re: J-Head not heating.]]> https://www.soliforum.com/post/30164/#p30164 The nice thing about the heater cartridge is it comes with a nice long cord.  I ran mine all the way back to the board, so I don't need to worry about any bad connections.  If I need to take the hot end out, the cartridge stays behind.

]]> Thu, 18 Jul 2013 04:58:03 +0000 https://www.soliforum.com/post/30164/#p30164 <![CDATA[Re: J-Head not heating.]]> https://www.soliforum.com/post/30161/#p30161 As expected started looking at the wires and found a wire broken right at the solder joint.  Going to just replace those thin OEM wires from the board to the hotend this weekend.

]]> Thu, 18 Jul 2013 04:50:41 +0000 https://www.soliforum.com/post/30161/#p30161 <![CDATA[Re: J-Head not heating.]]> https://www.soliforum.com/post/29971/#p29971 yes in portland big_smile

Just never heard of Dorkbotpdx. may have to check it out big_smile

And after I posted that it seemed to be working, back to not working.  Resistor still shows resistance.  But it just wont heat up now.  Repeteir shows that it is trying to send the command just get nothing from the hot end. I checked for voltage at the resistor and nothing.

Turns out I have a broken wire or solder joint at the 4pin ATX header I use for my hotend and thermistor connection at the side of my extruder.  Work on it more tomarrow.

]]> Tue, 16 Jul 2013 05:07:34 +0000 https://www.soliforum.com/post/29971/#p29971 <![CDATA[Re: J-Head not heating.]]> https://www.soliforum.com/post/29968/#p29968 I just saw PDX and assumed you where in the same town (Portland). Should check it out.. full of people itching to tackle projects (its a local hackerspace)

http://dorkbotpdx.org/

(They do 3d printing lots too, and drones etc... )

]]> Tue, 16 Jul 2013 04:30:46 +0000 https://www.soliforum.com/post/29968/#p29968 <![CDATA[Re: J-Head not heating.]]> https://www.soliforum.com/post/29967/#p29967 never heard of that.

And once home used a multimeter and the resistor is getting 6.4ohms like it should. reconnected and now able to heat again.  trying a print right now.

]]> Tue, 16 Jul 2013 04:27:57 +0000 https://www.soliforum.com/post/29967/#p29967 <![CDATA[Re: J-Head not heating.]]> https://www.soliforum.com/post/29965/#p29965 You hang out at DorkBot PDX (home of the purple PCB) much/ever ?

]]> Tue, 16 Jul 2013 03:48:45 +0000 https://www.soliforum.com/post/29965/#p29965 <![CDATA[J-Head not heating.]]> https://www.soliforum.com/post/29951/#p29951 Was at a PDXLan party this weekend, so Have not had a chance to trouble shoot yet.  But the hot end stopped heating. Have to get a look at it when I get home. I think the resistor stopped resisting..... Time to get a heater cartridge big_smile

]]> Mon, 15 Jul 2013 23:15:14 +0000 https://www.soliforum.com/post/29951/#p29951