<![CDATA[SoliForum - 3D Printing Community — Extruder issue]]> https://www.soliforum.com/topic/3155/extruder-issue/ Fri, 02 Aug 2013 15:27:00 +0000 PunBB <![CDATA[Re: Extruder issue]]> https://www.soliforum.com/post/31731/#p31731 Every time that the bed is not calibrated (usually i have to recalibrate it after two prints) , the plastic get stuck in the extruder. To remove the clogged nozzle i can't use the guitar string because doesn't work, I have to open the extruder and clean the inside. It only happens to me so often?

]]> Fri, 02 Aug 2013 15:27:00 +0000 https://www.soliforum.com/post/31731/#p31731 <![CDATA[Re: Extruder issue]]> https://www.soliforum.com/post/30640/#p30640 I would say anything less than .3mm.  The new nozzles are .4mm, but I'm not sure what size you have, so going with the smaller size is a good bet in any case.

]]> Mon, 22 Jul 2013 23:00:58 +0000 https://www.soliforum.com/post/30640/#p30640 <![CDATA[Re: Extruder issue]]> https://www.soliforum.com/post/30632/#p30632 Sorry for the delay, in my country I could not find the guitar string E (i don't play guitar so i'm not skilled in this things) anyway could you tell me the thickness of that string? Thanks for the help smile

]]> Mon, 22 Jul 2013 21:44:37 +0000 https://www.soliforum.com/post/30632/#p30632 <![CDATA[Re: Extruder issue]]> https://www.soliforum.com/post/29744/#p29744 You shouldn't have to take it apart for this part of the operations...  Lower the bed >30mm and use the guitar string from the bottom of the nozzle.  Insert it until you start getting some ooze out of the nozzle around the string. remove the string and extrude 20-40mm to complete the clear.

If this doesn't clear it, then you may have to clear it by taking it apart and torching the nozzle, but let's not go that far first.

]]> Sat, 13 Jul 2013 15:42:22 +0000 https://www.soliforum.com/post/29744/#p29744 <![CDATA[Re: Extruder issue]]> https://www.soliforum.com/post/29738/#p29738 For this type of operation I have to disassemble the extruder piece by piece? In case it is not a problem I've done that a few times..

]]> Sat, 13 Jul 2013 13:59:39 +0000 https://www.soliforum.com/post/29738/#p29738 <![CDATA[Re: Extruder issue]]> https://www.soliforum.com/post/29689/#p29689 You, my friend, have a clogged nozzle.  first step is to try to clear the nozzle using a guitar wire (E string, I believe).  Careful, you may burn a finger or two as the nozzle gets hot!

]]> Fri, 12 Jul 2013 22:16:36 +0000 https://www.soliforum.com/post/29689/#p29689 <![CDATA[Extruder issue]]> https://www.soliforum.com/post/29687/#p29687 Hi guys during my last print after same layers the extruder has ceased to extrude the plastic, i made a little video: https://www.youtube.com/watch?v=-JX1ZA-U8Uc. The motor do not seem to make more grip on the plastic filament how i can resolve this issue? Thanks for any type of help that will you give me.

]]> Fri, 12 Jul 2013 21:47:21 +0000 https://www.soliforum.com/post/29687/#p29687