<![CDATA[SoliForum - 3D Printing Community — Cartouche de chauffe]]> https://www.soliforum.com/topic/2943/cartouche-de-chauffe/ Tue, 25 Jun 2013 16:20:54 +0000 PunBB <![CDATA[Re: Cartouche de chauffe]]> https://www.soliforum.com/post/27915/#p27915 J en sais rien..Mais celle de la mienne (SD3) elle est pas enorme.... Ca m etonnerait qu ils y ait mis une plus petire quand meme...

]]> Tue, 25 Jun 2013 16:20:54 +0000 https://www.soliforum.com/post/27915/#p27915 <![CDATA[Re: Cartouche de chauffe]]> https://www.soliforum.com/post/27910/#p27910 Oui mais est-ce que l'alimentation de la SD3 est la même que celle de la SD 2 ?

]]> Tue, 25 Jun 2013 16:06:22 +0000 https://www.soliforum.com/post/27910/#p27910 <![CDATA[Re: Cartouche de chauffe]]> https://www.soliforum.com/post/27909/#p27909 Oui elle marche tres bien sur la SD
C est ce que j ai mis (du meme fournisseur)et ca marche et c est une qualité meilleure que celle d origine. !!!!
LE seul ennui c est que le diametre du corps de chauffe est plus petit....
Moi j y ai mis un bloqueur dedans.....

]]> Tue, 25 Jun 2013 15:59:17 +0000 https://www.soliforum.com/post/27909/#p27909 <![CDATA[Re: Cartouche de chauffe]]> https://www.soliforum.com/post/27893/#p27893 ok thanks a lot wink

]]> Tue, 25 Jun 2013 15:02:35 +0000 https://www.soliforum.com/post/27893/#p27893 <![CDATA[Re: Cartouche de chauffe]]> https://www.soliforum.com/post/27886/#p27886 Hmm, I'm not familiar with the SD2 power supply.
The cartridge at 100% will need 3.3 Amps. The existing Resistor uses 2.5 Amps - so it needs 800ma more. This might be ok on your power supply.

You can limit the cartridge to only be able to run at 80%, which will slightly slow down heatup time, but will mean it only draws 2.5Amps. This is a setting in firmware.

I have long since upgraded my heated bed, so have a much more powerful power supply anyway.

Someone with an SD2 can perhaps confirm what the existing power supply is capable of - it might be able to take the extra 800ma just fine (thats not big in the scheme of things....)

]]> Tue, 25 Jun 2013 14:43:45 +0000 https://www.soliforum.com/post/27886/#p27886 <![CDATA[Re: Cartouche de chauffe]]> https://www.soliforum.com/post/27883/#p27883 Thanks a lot !
so the power unit that came with the SD2 is strong enough for this ?

]]> Tue, 25 Jun 2013 14:37:35 +0000 https://www.soliforum.com/post/27883/#p27883 <![CDATA[Re: Cartouche de chauffe]]> https://www.soliforum.com/post/27879/#p27879 Maybe - the existing resistor bore hole on mine was 5mm. Your listing is 5.5.

I hand reamed it using a 6mm drill bit (the cartridge I used was 6mm)  that I inserted in a drill press and turned by hand to slightly ream the hole. I didn't need power to the drill - the heater block is very very soft.

You can not replace the insulation once installed - the cartridge extends beyond the heater block. So you will need some cotton insulation wrap, or lots of Kapton.

]]> Tue, 25 Jun 2013 14:18:34 +0000 https://www.soliforum.com/post/27879/#p27879 <![CDATA[Cartouche de chauffe]]> https://www.soliforum.com/post/27876/#p27876 Est-il possible de mettre une cartouche de chauffe ceramic 12v 40 W  sur la SD 2 sans changer l'alimentation ?
comme celle ci par exermple:
http://www.reprap-france.com/electroniq … v-40w.html

]]> Tue, 25 Jun 2013 14:00:50 +0000 https://www.soliforum.com/post/27876/#p27876