<![CDATA[SoliForum - 3D Printing Community — Set screw for Extruder Gear]]> https://www.soliforum.com/topic/2408/set-screw-for-extruder-gear/ Fri, 17 May 2013 05:22:51 +0000 PunBB <![CDATA[Re: Set screw for Extruder Gear]]> https://www.soliforum.com/post/23079/#p23079 elmoret wrote:
cckens wrote:

I just noticed... LOL...

I can get the hex in fine, but turning it is going to take some rocking to crack the glue.

Guess I'm going to have to put some back in when I get it into position.

I've never needed any.

I never put any threadlocker on when I put them back together either.. but then again I also put a flat spot on the stepper shaft so the setscrew would lock down better.

]]> Fri, 17 May 2013 05:22:51 +0000 https://www.soliforum.com/post/23079/#p23079 <![CDATA[Re: Set screw for Extruder Gear]]> https://www.soliforum.com/post/23073/#p23073 cckens wrote:

I just noticed... LOL...

I can get the hex in fine, but turning it is going to take some rocking to crack the glue.

Guess I'm going to have to put some back in when I get it into position.

I've never needed any.

]]> Fri, 17 May 2013 04:05:52 +0000 https://www.soliforum.com/post/23073/#p23073 <![CDATA[Re: Set screw for Extruder Gear]]> https://www.soliforum.com/post/23068/#p23068 I just noticed... LOL...

I can get the hex in fine, but turning it is going to take some rocking to crack the glue.

Guess I'm going to have to put some back in when I get it into position.

]]> Fri, 17 May 2013 03:31:23 +0000 https://www.soliforum.com/post/23068/#p23068 <![CDATA[Re: Set screw for Extruder Gear]]> https://www.soliforum.com/post/23062/#p23062 When you find an allen key for it you might have to work it in there as SD puts cyanoacrylate on the threads to lock them and sometimes a little bit gets inside the setscrew.

]]> Fri, 17 May 2013 02:33:01 +0000 https://www.soliforum.com/post/23062/#p23062 <![CDATA[Re: Set screw for Extruder Gear]]> https://www.soliforum.com/post/23007/#p23007 Thanks, ronsii... that's what I'm looking for!  Just need to get a metric set that small.

]]> Thu, 16 May 2013 15:14:05 +0000 https://www.soliforum.com/post/23007/#p23007 <![CDATA[Re: Set screw for Extruder Gear]]> https://www.soliforum.com/post/22977/#p22977 If you mean the driver size for the setscrew it is 1.5mm

]]> Thu, 16 May 2013 05:12:07 +0000 https://www.soliforum.com/post/22977/#p22977 <![CDATA[Set screw for Extruder Gear]]> https://www.soliforum.com/post/22914/#p22914 Anyone know what the size is for the set screw on the Extruder gear?

My Mk4 assembly is a bit off for feeding into the hot end and I think this is causing some of my extrusion issues.

]]> Wed, 15 May 2013 21:17:10 +0000 https://www.soliforum.com/post/22914/#p22914