<![CDATA[SoliForum - 3D Printing Community — Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/topic/2162/perimeter-infill-and-flow-rate-issues/ Wed, 24 Apr 2013 06:28:46 +0000 PunBB <![CDATA[Re: Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20831/#p20831 I do like Ian said, and adjust for these kinds of things in the slicing software.

]]> Wed, 24 Apr 2013 06:28:46 +0000 https://www.soliforum.com/post/20831/#p20831 <![CDATA[Re: Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20829/#p20829 Really no ones has had this problem before?

]]> Wed, 24 Apr 2013 05:21:34 +0000 https://www.soliforum.com/post/20829/#p20829 <![CDATA[Re: Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20761/#p20761 200c?

]]> Tue, 23 Apr 2013 17:09:28 +0000 https://www.soliforum.com/post/20761/#p20761 <![CDATA[Re: Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20759/#p20759 Maybe your temp is too low

]]> Tue, 23 Apr 2013 16:57:55 +0000 https://www.soliforum.com/post/20759/#p20759 <![CDATA[Re: Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20758/#p20758 What if you set a larger extrusion width in Slic3r for different areas?  Like .42 for perimeters, and .5 for solid infill.

]]> Tue, 23 Apr 2013 16:55:02 +0000 https://www.soliforum.com/post/20758/#p20758 <![CDATA[Re: Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20756/#p20756 Yes that is what causes my problem.  If I over extrude it works fine.  If I set my extrusion to be perfect it has seperated perimiters from infill.

]]> Tue, 23 Apr 2013 16:38:35 +0000 https://www.soliforum.com/post/20756/#p20756 <![CDATA[Re: Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20730/#p20730 I used this method and most of my problems went away.

http://www.soliwiki.com/Calibrate_Filament_Flow

]]> Tue, 23 Apr 2013 11:50:53 +0000 https://www.soliforum.com/post/20730/#p20730 <![CDATA[Re: Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20716/#p20716 You can try different slicers and see if they help. I would tweak your extrusion multiplier till you get something in between the two.

]]> Tue, 23 Apr 2013 06:11:24 +0000 https://www.soliforum.com/post/20716/#p20716 <![CDATA[Perimeter, Infill, and Flow Rate issues.]]> https://www.soliforum.com/post/20711/#p20711 So having perfectly adjusted my extrusion settings so i get .42mm wide extrusion I have problems with infill not meeting perimiters.  If I over extrude I get really strong parts with great infill/perimeter meetup, but at .42mm I have gaps like the picture below.  Please help.

Edit:  this happens with both kisslicer and slic3r

http://www.pdxmc.com/uploads/SD3/20130422_210834.jpg

]]> Tue, 23 Apr 2013 05:01:08 +0000 https://www.soliforum.com/post/20711/#p20711