SoliForum - 3D Printing Community — in fill issue with 1 mm profile

Re: in fill issue with 1 mm profile

null@example.com (Arcadenut) — Tue, 16 Apr 2013 17:33:50 +0000

Calibrate for the Flow Rate. I have that issue when the gear slips on the gear shaft. I used a sharpie to mark the gear and the gear shaft. If it slips the marks will no longer be lined up and you'll need to tighten the gear down.

You could also cut the infill speed way down and see if that improves things. The down side would be that prints would take a lot longer to print.

Re: in fill issue with 1 mm profile

null@example.com ([SOLARiS]) — Tue, 16 Apr 2013 13:05:50 +0000

@CrazyBear Thanks for sharing your profiles. After some minor tweaking for my SD2 I got my best .1mm print to date. Now I just need to solve my Z axis banding issues.

Re: in fill issue with 1 mm profile

null@example.com ([SOLARiS]) — Fri, 12 Apr 2013 13:26:44 +0000

CrazyBear wrote:

[SOLARiS] wrote:
CrazyBear wrote:
I printed this owl at 0.05 mm using Slic3r 0.9.9 and setting avoiding to cross perimeters and printing infill before perimeters. No fan installed (yet).
CB
I have updated RH and tried these settings. The print was slightly better but still not great.
I was wondering if someone would be willing to share their profile for .1mm printing so I can compare my settings.

Here you go. Note that is for a SD3

Thanks, I'll check it out and report back.

Re: in fill issue with 1 mm profile

null@example.com (CrazyBear) — Fri, 12 Apr 2013 02:23:39 +0000

[SOLARiS] wrote:

CrazyBear wrote:
I printed this owl at 0.05 mm using Slic3r 0.9.9 and setting avoiding to cross perimeters and printing infill before perimeters. No fan installed (yet).
CB
I have updated RH and tried these settings. The print was slightly better but still not great.
I was wondering if someone would be willing to share their profile for .1mm printing so I can compare my settings.

Here you go. Note that is for a SD3

Re: in fill issue with 1 mm profile

null@example.com (op7ical) — Thu, 11 Apr 2013 13:45:35 +0000

Try infilling on every layer, rather than every third. One possibility is that you are getting adhesion issues. This is worsened since the extruder is now three times the layer height above the surface you are depositing on, and it can't push down on the filament properly as it extrudes. Thus, if you have any problems with adhesion, the filament will just drag along with the extruder and make a mess.

Re: in fill issue with 1 mm profile

null@example.com ([SOLARiS]) — Thu, 11 Apr 2013 12:53:31 +0000

CrazyBear wrote:

I printed this owl at 0.05 mm using Slic3r 0.9.9 and setting avoiding to cross perimeters and printing infill before perimeters. No fan installed (yet).
CB

I have updated RH and tried these settings. The print was slightly better but still not great.

I was wondering if someone would be willing to share their profile for .1mm printing so I can compare my settings.

Re: in fill issue with 1 mm profile

null@example.com (CrazyBear) — Wed, 10 Apr 2013 04:54:06 +0000

I printed this owl at 0.05 mm using Slic3r 0.9.9 and setting avoiding to cross perimeters and printing infill before perimeters. No fan installed (yet).

Re: in fill issue with 1 mm profile

null@example.com ([SOLARiS]) — Tue, 09 Apr 2013 21:53:55 +0000

mm2tts wrote:

I've found that for .1mm printing you may need to run your extrusion cooler and use a fan. The thin infill just melts when the extruder head passes over.

I have tried that. I use a fan for .3mm printing all the time. It's almost like the printer isn't extruding enough plastic.

Re: in fill issue with 1 mm profile

null@example.com (Jonathan) — Tue, 09 Apr 2013 20:14:27 +0000

I too am having this issue.

Re: in fill issue with 1 mm profile

null@example.com (mm2tts) — Tue, 09 Apr 2013 16:21:37 +0000

I've found that for .1mm printing you may need to run your extrusion cooler and use a fan. The thin infill just melts when the extruder head passes over.

Re: in fill issue with 1 mm profile

null@example.com ([SOLARiS]) — Tue, 09 Apr 2013 14:56:50 +0000

I'm having the same exact problem. No matter what I try I can't get a good .1mm print. I would be interested to know if you have been able to resolve the infill issue. I tried SD tech support but after a period of time I gave up with them.

Re: in fill issue with 1 mm profile

null@example.com (iowajames) — Sun, 07 Apr 2013 20:05:07 +0000

WOW! How did you get that cat to look so realistic? Does someone produce fur filament now?????

Maybe change infill density to .1 or make a hollow piece with thick outer walls?

Re: in fill issue with 1 mm profile

null@example.com (LordThrash) — Sun, 07 Apr 2013 18:39:51 +0000

Yes RH and already using infill every 3 layers with .2 fill density. The Fill Pattern is Rectilinear and the Top/Bottom fill pattern is Concentric.

Final piece is not so pretty. It seems I cant get fine lines stay connected. This is using Octave grey ABS, but I was getting similar results with Solidoodles Natural filamement.

Re: in fill issue with 1 mm profile

null@example.com (iowajames) — Sun, 07 Apr 2013 05:10:54 +0000

Hmmm, I assume you use RH as your interface, I recommend setting your infill to "Infill every 3 layers" instead of infill every 1 layers when printing in .1 mm resolution. See if that works. I haven't tried it, but I am going on the idea that mine infills fine every layer when printing .3 mm resolution, so infill every third layer during .1 mm prints = every .3 mm basically, maybe it may work? Maybe just try setting it to infill every 2 layers first, wouldn't hurt to try anyway.

HTH!

Edit: Please let us know, I will be attempting a .1 mm print for the first time tomorrow.

in fill issue with 1 mm profile

null@example.com (LordThrash) — Sun, 07 Apr 2013 04:19:09 +0000

I have trying prints for a month or 2 with my S3 and the default .3 mm profile with slic3r works pretty well. The .1mm totaly fails to do the infill crosshatches. It looks like a mess leaving the top surfaces with gaps. Suggestions? I have not calibrated my extruding ever since the .3 worked fine.