<![CDATA[SoliForum - 3D Printing Community — Ord Solutions MH3000-5 giving errors]]> https://www.soliforum.com/topic/18938/ord-solutions-mh30005-giving-errors/ Sat, 16 Oct 2021 12:13:34 +0000 PunBB <![CDATA[Re: Ord Solutions MH3000-5 giving errors]]> https://www.soliforum.com/post/155027/#p155027 generally speaking, around 20C is acceptable to "most" printers... i think mine read about 21 or so on average

]]> Sat, 16 Oct 2021 12:13:34 +0000 https://www.soliforum.com/post/155027/#p155027 <![CDATA[Re: Ord Solutions MH3000-5 giving errors]]> https://www.soliforum.com/post/155026/#p155026 Oh Thank you! So it may just ne the fact I have it in my shop (not heated!)
I am glad I did include the temp. Not sure which was which, I think the bed was 17c and the nozzles were 18c.
I do understand what you are saying.
I will test it this weekend.

How warm/hot should they be? 22-25C?

Who would have thought that being too COLD would send a error for too hot!
Some programming logic should be done on the error message portion of the firmware/software to trap that and put out a correct message smile


Thank you very very much!
Bruj

]]> Sat, 16 Oct 2021 01:47:56 +0000 https://www.soliforum.com/post/155026/#p155026 <![CDATA[Re: Ord Solutions MH3000-5 giving errors]]> https://www.soliforum.com/post/155025/#p155025 bruj wrote:

I moved and I have finally had a chance to unpack my 3D printer (several years have passed...)
Anyways, I am getting a:
: Extruder switched off. MAXTEMP triggered !
Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset.
but I have no idea how to resolve this.
This is when I FIRST connect, and the nozzles have not even been turned on yet. They are reading 18C.

I have sent several messages this week to Ord with no reply, and I cannot find a phone number (the only number I find reached a pill company)
Can someone give me some guidance?

Is it actually 18c where the printer is setting? If so then you need to either warm the nozzle and bed with a hair dryer or move the printer to a warmer area. The system has a safety feature that assumes a temp below a certain point means a bad thermistor so it shuts down for safety. If it is not that cold then your thermistors are bad are your wiring from them to the boar are bad or you have a bad connection at the board.

]]> Sat, 16 Oct 2021 00:12:00 +0000 https://www.soliforum.com/post/155025/#p155025 <![CDATA[Ord Solutions MH3000-5 giving errors]]> https://www.soliforum.com/post/155024/#p155024 I moved and I have finally had a chance to unpack my 3D printer (several years have passed...)
Anyways, I am getting a:
: Extruder switched off. MAXTEMP triggered !
Error:Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset.
but I have no idea how to resolve this.
This is when I FIRST connect, and the nozzles have not even been turned on yet. They are reading 18C.

I have sent several messages this week to Ord with no reply, and I cannot find a phone number (the only number I find reached a pill company)
Can someone give me some guidance?

]]> Fri, 15 Oct 2021 18:35:06 +0000 https://www.soliforum.com/post/155024/#p155024