<![CDATA[SoliForum - 3D Printing Community — Da Vinci Jr: Extruder Cooler?]]> https://www.soliforum.com/topic/18852/da-vinci-jr-extruder-cooler/ Tue, 30 Mar 2021 14:03:20 +0000 PunBB <![CDATA[Re: Da Vinci Jr: Extruder Cooler?]]> https://www.soliforum.com/post/154633/#p154633 Ethereal wrote:
modfreakz wrote:

Could you please tke few photos of "getting flattened Filament"

Not my image but it looks like this

Radial fan seems like a good idea! I'm guessing I could just drill some holes in the side of the case and screw it on actually smile

I tried printing my object with retraction disabled and it printed successfully so I'm pretty sure that adding some cooling will help. I did feel the motor while running and it didn't feel too hot actually, so I'm wondering if adjusting the spring tension is a good idea also. I haven't seen any howtos on that but might disassemble the case to get to it. Unfortunately it seems like that whole assembly is not made to be serviced...

]]> Tue, 30 Mar 2021 14:03:20 +0000 https://www.soliforum.com/post/154633/#p154633 <![CDATA[Re: Da Vinci Jr: Extruder Cooler?]]> https://www.soliforum.com/post/154632/#p154632 That's the first mod I made to my Jr as the motor did get quite hot.
I added a radial fan to blow on the extruder motor.
I took the 12v  from the rear fan.
Printed a small mounting plate for it and it sits offset but below the motor and keeps it cool.
Never had the issue since

Am at work so can't give you a pic.

]]> Tue, 30 Mar 2021 07:12:20 +0000 https://www.soliforum.com/post/154632/#p154632 <![CDATA[Re: Da Vinci Jr: Extruder Cooler?]]> https://www.soliforum.com/post/154627/#p154627 modfreakz wrote:

Could you please tke few photos of "getting flattened Filament"

Not my image but it looks like this

]]> Mon, 29 Mar 2021 15:29:40 +0000 https://www.soliforum.com/post/154627/#p154627 <![CDATA[Re: Da Vinci Jr: Extruder Cooler?]]> https://www.soliforum.com/post/154626/#p154626 Could you please tke few photos of "getting flattened Filament"

]]> Mon, 29 Mar 2021 06:10:41 +0000 https://www.soliforum.com/post/154626/#p154626 <![CDATA[Re: Da Vinci Jr: Extruder Cooler?]]> https://www.soliforum.com/post/154625/#p154625 modfreakz wrote:

Hi,

do you mean something like that, but only for Junior?

https://www.ebay.de/itm/124441930555

I think I need something to cool the extruder motor actually, the gears that push filament into the nozzle. Due to retraction the filament seems to be getting flattened when going through the drive gears repeatedly, and I'm thinking it's because the filament is getting warm

]]> Mon, 29 Mar 2021 05:10:46 +0000 https://www.soliforum.com/post/154625/#p154625 <![CDATA[Re: Da Vinci Jr: Extruder Cooler?]]> https://www.soliforum.com/post/154624/#p154624 Hi,

do you mean something like that, but only for Junior?

https://www.ebay.de/itm/124441930555

]]> Sun, 28 Mar 2021 20:37:55 +0000 https://www.soliforum.com/post/154624/#p154624 <![CDATA[Da Vinci Jr: Extruder Cooler?]]> https://www.soliforum.com/post/154622/#p154622 My extruder is heating up and flattening filament on complex prints with lots of retracts. Has anyone made a mod to work around this? I'm wondering if I can remove the casing to let it breathe more, or add a fan but haven't found any evidence that this has been tried.

No, I'm not talking about a fan for the hotend but rather for the extruder smile

]]> Sun, 28 Mar 2021 17:50:41 +0000 https://www.soliforum.com/post/154622/#p154622