<![CDATA[SoliForum - 3D Printing Community — XYZ DaVinci 1.0 Pro print head wire disconnection]]> https://www.soliforum.com/topic/18784/xyz-davinci-10-pro-print-head-wire-disconnection/ Sun, 06 Dec 2020 20:01:34 +0000 PunBB <![CDATA[Re: XYZ DaVinci 1.0 Pro print head wire disconnection]]> https://www.soliforum.com/post/154250/#p154250 You can see the shorter wire sticking out. That is where the break was, Yes it is bad for the wires to touch. The both need to be insulated from each other and anything around them.

]]> Sun, 06 Dec 2020 20:01:34 +0000 https://www.soliforum.com/post/154250/#p154250 <![CDATA[Re: XYZ DaVinci 1.0 Pro print head wire disconnection]]> https://www.soliforum.com/post/154248/#p154248 Would i solder them back into the same spot? do they go together? Will it cause issues if they touch?

]]> Sun, 06 Dec 2020 01:06:00 +0000 https://www.soliforum.com/post/154248/#p154248 <![CDATA[Re: XYZ DaVinci 1.0 Pro print head wire disconnection]]> https://www.soliforum.com/post/154247/#p154247 Would it short or cause damage to the printer if we try soldering it and it doesnt go to the right spot by chance?

]]> Sun, 06 Dec 2020 01:03:12 +0000 https://www.soliforum.com/post/154247/#p154247 <![CDATA[Re: XYZ DaVinci 1.0 Pro print head wire disconnection]]> https://www.soliforum.com/post/154246/#p154246 Yep that is a thermistor wire. The issue though is those are usually nickle and won't solder but you can try. You might also look into removing the old one which might require heating and then replacing the thermistor.

]]> Sun, 06 Dec 2020 00:46:56 +0000 https://www.soliforum.com/post/154246/#p154246 <![CDATA[Re: XYZ DaVinci 1.0 Pro print head wire disconnection]]> https://www.soliforum.com/post/154245/#p154245 http://soliforum.com/i/?DirFMBB.jpg

]]> Sat, 05 Dec 2020 23:43:44 +0000 https://www.soliforum.com/post/154245/#p154245 <![CDATA[Re: XYZ DaVinci 1.0 Pro print head wire disconnection]]> https://www.soliforum.com/post/154244/#p154244 mathew9a wrote:

Hello Everyone!
I purchased an XYZ DaVinci 1.0 Pro printer about a year ago with my print head. My printer has been running and printing perfectly since, however recently I was printing something and one of the wires that comes out of the extruder came undone and the printer does not seem to have any idea what the temperature is because of this and won't print. I can solder it back in however I want to make sure that it does not need to go in a specific area aside from just on the outside area where the other wire is located. Can anyone help me with this? I would rather try to solder the wire back on over purchasing a new print head.

A picture would be helpful to see just where the wire broke from.

]]> Sat, 05 Dec 2020 23:35:29 +0000 https://www.soliforum.com/post/154244/#p154244 <![CDATA[XYZ DaVinci 1.0 Pro print head wire disconnection]]> https://www.soliforum.com/post/154243/#p154243 Hello Everyone!
I purchased an XYZ DaVinci 1.0 Pro printer about a year ago with my print head. My printer has been running and printing perfectly since, however recently I was printing something and one of the wires that comes out of the extruder came undone and the printer does not seem to have any idea what the temperature is because of this and won't print. I can solder it back in however I want to make sure that it does not need to go in a specific area aside from just on the outside area where the other wire is located. Can anyone help me with this? I would rather try to solder the wire back on over purchasing a new print head.

]]> Sat, 05 Dec 2020 22:31:34 +0000 https://www.soliforum.com/post/154243/#p154243