<![CDATA[SoliForum - 3D Printing Community — Davinci 3d printer aio flash repetier host with out lcd panel]]> https://www.soliforum.com/topic/18606/davinci-3d-printer-aio-flash-repetier-host-with-out-lcd-panel/ Sat, 16 May 2020 23:14:48 +0000 PunBB <![CDATA[Re: Davinci 3d printer aio flash repetier host with out lcd panel]]> https://www.soliforum.com/post/153340/#p153340 You should not be saving anything to eeprom. That is not firmware. The firmware is written to the processor. Settings are written to the eeprom. If you use the software XYZ supplies it has an update firmware function. You can also print from it. Many printers even now do not have LCD's but you can can do everything you need through an official or third party host.

]]> Sat, 16 May 2020 23:14:48 +0000 https://www.soliforum.com/post/153340/#p153340 <![CDATA[Re: Davinci 3d printer aio flash repetier host with out lcd panel]]> https://www.soliforum.com/post/153339/#p153339 i expect the software for the computer has similar options.
Again I have no experience with the davinici and do not care to.

]]> Sat, 16 May 2020 17:02:03 +0000 https://www.soliforum.com/post/153339/#p153339 <![CDATA[Re: Davinci 3d printer aio flash repetier host with out lcd panel]]> https://www.soliforum.com/post/153338/#p153338 Many thanks - the options I refer to is on all the "how to" videos I have seen - images
I guess if I was to go into the  code, I could change the hash defines which relates to the default "no" or hack the code itself
but just wanted to see if any one else had are more elegant approach
http://soliforum.com/i/?D0npwXb.png

http://soliforum.com/i/?gkduDMQ.png

]]> Sat, 16 May 2020 15:44:40 +0000 https://www.soliforum.com/post/153338/#p153338 <![CDATA[Re: Davinci 3d printer aio flash repetier host with out lcd panel]]> https://www.soliforum.com/post/153336/#p153336 do not know the davinci. I do know Open sourced boards have been flashed and updated for years with no lcd screen. the solidoodle  was shipped that way. The have to be tethered to the computer.

]]> Sat, 16 May 2020 12:11:20 +0000 https://www.soliforum.com/post/153336/#p153336 <![CDATA[Re: Davinci 3d printer aio flash repetier host with out lcd panel]]> https://www.soliforum.com/post/153330/#p153330 That’s why there’s a “delete topic” button.

]]> Fri, 15 May 2020 21:53:32 +0000 https://www.soliforum.com/post/153330/#p153330 <![CDATA[Re: Davinci 3d printer aio flash repetier host with out lcd panel]]> https://www.soliforum.com/post/153328/#p153328 Sorry about duplicate posts

Fat Boke -> Fat Fingers

]]> Fri, 15 May 2020 21:10:33 +0000 https://www.soliforum.com/post/153328/#p153328 <![CDATA[Davinci 3d printer aio flash repetier host with out lcd panel]]> https://www.soliforum.com/post/153327/#p153327 Davinci 3d printer aio flash repetier host with out lcd panel

I have killed my much loved Davinci 3d printer Aio by printing masks for the nhs

The lcd panel stopped working -- so I bridge r57 and added an inclined fuse - the 5v line burst into life

The panel would light for a minute or two, long enough for me to check that the poor thing still could print

Someone on this forum suggested in another  old post that the LCD was prone to failure and should be replaced.  So a got a winstar1604 lcd and did the worst replacement job ever. The old solder wasnt solder it was adamantium

Anyway the lcd board is a right-off

But the printer works.  Doing the research, I read that flashing the  aio with repetier host is feasable.

But how do I save the new firmware to eeprom without an  lcd/key panel, the example videos all show the final stage as using the lcd panel to safe with yes | no options

Also if it works can I unload, load and calibrate from the PC?


Or should it all go in the bin

]]> Fri, 15 May 2020 21:03:07 +0000 https://www.soliforum.com/post/153327/#p153327