<![CDATA[SoliForum - 3D Printing Community — Hi all]]> https://www.soliforum.com/topic/18503/hi-all/ Tue, 07 Apr 2020 13:38:28 +0000 PunBB <![CDATA[Re: Hi all]]> https://www.soliforum.com/post/152938/#p152938 hokiechef wrote:

@heartless
Could you tell me where to look for the part that I can buy? And what it's called?
I had tried Repetier but it asked me for all sorts of info to connect to the machine that I had no idea what the answers were so I ended up uninstalling. I will try again. ;-) Thank you!

there is no where to just outright buy it. but it can be re-printed (at a higher infill than stock)

and I am more than willing to help you set things up properly, once that piece is replaced.

]]> Tue, 07 Apr 2020 13:38:28 +0000 https://www.soliforum.com/post/152938/#p152938 <![CDATA[Re: Hi all]]> https://www.soliforum.com/post/152926/#p152926 @heartless
Could you tell me where to look for the part that I can buy? And what it's called?
I had tried Repetier but it asked me for all sorts of info to connect to the machine that I had no idea what the answers were so I ended up uninstalling. I will try again. ;-) Thank you!

]]> Tue, 07 Apr 2020 00:11:51 +0000 https://www.soliforum.com/post/152926/#p152926 <![CDATA[Re: Hi all]]> https://www.soliforum.com/post/152916/#p152916 @hokiechef - super easy part to replace, and if you need help with that, I am more than willing to help out.

now, for software, go download Repetier Host and ditch Soliprint - that was mostly intended for the Press, not the SD4. Yes, it will work, but there are better alternatives.

and welcome aboard to both of you. wink

]]> Mon, 06 Apr 2020 03:10:53 +0000 https://www.soliforum.com/post/152916/#p152916 <![CDATA[Re: Hi all]]> https://www.soliforum.com/post/152915/#p152915 Hi there! Yesterday I dug out a Solidoodle 4 that I bought 5+ years ago and was never used. I was able to install Soliprint, successfully got it hooked up to my computer and managed a small test print that mostly looked like I expected, but haven't been able to get anything else to work. Today I realized that the extruder was not close enough to the bed on one side, but I couldn't get it adjusted at all using the wingnuts.  I also realized that the Hand Adjusted Z-Tab was not in right and had broken (pics attached).  Novice doesn't even begin to describe me here. I don't know if I could replace the part that broke or if I should give up and stick it in a closet for another 5 years. Open to suggestions or ideas! http://soliforum.com/i/?v6aVzK5.jpg

]]> Mon, 06 Apr 2020 02:00:31 +0000 https://www.soliforum.com/post/152915/#p152915 <![CDATA[Re: Hi all]]> https://www.soliforum.com/post/152908/#p152908 Welcome

]]> Sun, 05 Apr 2020 17:35:44 +0000 https://www.soliforum.com/post/152908/#p152908 <![CDATA[Hi all]]> https://www.soliforum.com/post/152886/#p152886 Hi all,

I am glad to be part of this forum, I hope I can help and learn much from the community.

Regards
Emanuele

]]> Fri, 03 Apr 2020 07:14:29 +0000 https://www.soliforum.com/post/152886/#p152886