<![CDATA[SoliForum - 3D Printing Community — da Vinci Duo 2.0A Extruder Gear]]> https://www.soliforum.com/topic/18319/da-vinci-duo-20a-extruder-gear/ Wed, 04 Dec 2019 20:42:21 +0000 PunBB <![CDATA[Re: da Vinci Duo 2.0A Extruder Gear]]> https://www.soliforum.com/post/152074/#p152074 carl_m1968 wrote:
Bryan.byrne wrote:

I am having a similar problem with mine. Not printing consistently. I am thinking about replacing the entire assembly with one of these, I just need to figure out the number of steps between the nozzles to reflash the eeprom with.
https://www.amazon.com/dp/B07T9CQNSP/?c … _lig_dp_it


Unless you plan to buy a suitable carriage as well, this will not mount on the stock XYZ carriage.

Ingenuity

]]> Wed, 04 Dec 2019 20:42:21 +0000 https://www.soliforum.com/post/152074/#p152074 <![CDATA[Re: da Vinci Duo 2.0A Extruder Gear]]> https://www.soliforum.com/post/152070/#p152070 Bryan.byrne wrote:

I am having a similar problem with mine. Not printing consistently. I am thinking about replacing the entire assembly with one of these, I just need to figure out the number of steps between the nozzles to reflash the eeprom with.
https://www.amazon.com/dp/B07T9CQNSP/?c … _lig_dp_it


Unless you plan to buy a suitable carriage as well, this will not mount on the stock XYZ carriage.

]]> Tue, 03 Dec 2019 20:12:39 +0000 https://www.soliforum.com/post/152070/#p152070 <![CDATA[Re: da Vinci Duo 2.0A Extruder Gear]]> https://www.soliforum.com/post/152068/#p152068 I am having a similar problem with mine. Not printing consistently. I am thinking about replacing the entire assembly with one of these, I just need to figure out the number of steps between the nozzles to reflash the eeprom with.
https://www.amazon.com/dp/B07T9CQNSP/?c … _lig_dp_it

]]> Tue, 03 Dec 2019 19:52:19 +0000 https://www.soliforum.com/post/152068/#p152068 <![CDATA[Re: da Vinci Duo 2.0A Extruder Gear]]> https://www.soliforum.com/post/152063/#p152063 The silver wheel is an idler but it is also used in this machine to detect jams. There is an optical sensor on the board across from it that detects the light and dark patterns as it spins.

]]> Tue, 03 Dec 2019 11:23:02 +0000 https://www.soliforum.com/post/152063/#p152063 <![CDATA[da Vinci Duo 2.0A Extruder Gear]]> https://www.soliforum.com/post/152059/#p152059 I am looking for a replacement for both the brass and the silver drive wheel shown here in the pictures. My left extruder will not pull the filament anymore, or at least not consistently. That silver wheel is pretty wobbly compared to the other extruder (the other wobbles very very little). The brass gear is also pretty worn compared to the other. You can see how worn in the pictures. The other extruder has been barely used so you can see the difference. The springs look fine also I think.

I see that the silver wheel can probably come off pretty easily (not sure yet), I see just a plate attached and it will probably pop off. I just need a replacement. As for the brass wheel, that looks pressed on to the motor shaft. Would I have to buy a new motor with brass wheel attached already?

Has anyone dealt with this before?  Any idea where to get suitable parts or if this is even fixable?  I already put in a ticket with XYZPrinting support.  I'm not sure I will get anywhere with them but I figured I would try.

Also on a side note, what is that silver wheel and the brass gear called technically? Extruder gear, wheel, etc.?  Just so I am searching with the correct terminology.

]]> Tue, 03 Dec 2019 01:16:25 +0000 https://www.soliforum.com/post/152059/#p152059