SoliForum - 3D Printing Community — Slicer software Quality with my XYZ Davinci Ramps Conversion

Re: Slicer software Quality with my XYZ Davinci Ramps Conversion

null@example.com (ingdonovan) — Fri, 20 Apr 2018 12:56:33 +0000

i had problem with my X axis but is fixed now.. btw.. to be honest like you said, if i get better results with an app with no good printer calibration imagine with a properly calibrated printer.. so.. is the same thing.. but thanks advice.

Re: Slicer software Quality with my XYZ Davinci Ramps Conversion

null@example.com (carl_m1968) — Sun, 25 Feb 2018 20:41:35 +0000

ingdonovan wrote:

Hi all, i have a lot of days after my Da Vinci RAMPs 1.4 convertion, i was testing diferents softwares to see what happends and i see a huge change between all of them.
The best results i see is from Cura 3.2.1, but the problem is that i can't make the software use my G-Code starting procedure first and ending one, and i have to edit every gcode file exported before printing.
i tested 4 softwares:
- Slic3r 1.2.9 -- this is the one used since the first time. WORST
- Slic3r 1.34 Prusa Edition. Not too much differences with the first one
- Cura 3.2.1 -- best results but problem with setting for me.
- Simplify 3d 4.0 -- good so far
if someone have experience with CURA and could help me to set CURA correctly i would appretiate, and hope this information helpfull to decide wich software use.
THANKS

I am going to be brutally honest. All of those are pretty bad.

That being said have you properly calibrated your printed. Is your extruder steps per mm properly set?

I ask because you have a major over extrusion problem.

Are you actually measuring the filament diameter in several places and averaging it and using that value for the diameter in your slicer? Filament is never 1.75 and you cannot use that number.

Once you make sure your machine is properly calibrated then you work with getting the slicer set up. Personally I use Simplify3d and get great results.

Re: Slicer software Quality with my XYZ Davinci Ramps Conversion

null@example.com (mjf55) — Sun, 25 Feb 2018 18:22:28 +0000

I use Cura 3.2.0 and have no issues with the Start and End gcode commands.
From the main screen, Select Preferences -> Configure Cura -> Select Printers from the left side.
Highlight your printer profile to edit and press Machine Settings.
Now just change what you want.
When Done, press Close and close again.

I just tested that and it works fine.

Slicer software Quality with my XYZ Davinci Ramps Conversion

null@example.com (ingdonovan) — Sun, 25 Feb 2018 12:34:25 +0000

Hi all, i have a lot of days after my Da Vinci RAMPs 1.4 convertion, i was testing diferents softwares to see what happends and i see a huge change between all of them.

The best results i see is from Cura 3.2.1, but the problem is that i can't make the software use my G-Code starting procedure first and ending one, and i have to edit every gcode file exported before printing.

i tested 4 softwares:
- Slic3r 1.2.9 -- this is the one used since the first time. WORST
- Slic3r 1.34 Prusa Edition. Not too much differences with the first one
- Cura 3.2.1 -- best results but problem with setting for me.
- Simplify 3d 4.0 -- good so far

if someone have experience with CURA and could help me to set CURA correctly i would appretiate, and hope this information helpfull to decide wich software use.

THANKS