<![CDATA[SoliForum - 3D Printing Community — Filawinder always spinning]]> https://www.soliforum.com/topic/16980/filawinder-always-spinning/ Wed, 03 Jan 2018 08:26:59 +0000 PunBB <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141289/#p141289 There is now alot of room so it should be fine thanks

]]> Wed, 03 Jan 2018 08:26:59 +0000 https://www.soliforum.com/post/141289/#p141289 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141282/#p141282 Delloman,
If you have or can find some cheap heat shrink tubing that will fit over one of those it would prevent that from happening in the future.

-os3dp

]]> Tue, 02 Jan 2018 23:39:45 +0000 https://www.soliforum.com/post/141282/#p141282 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141278/#p141278 That was it they where touching

]]> Tue, 02 Jan 2018 20:45:49 +0000 https://www.soliforum.com/post/141278/#p141278 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141127/#p141127 with the way its acting in the video Id say its in auto mode.

]]> Wed, 27 Dec 2017 20:02:31 +0000 https://www.soliforum.com/post/141127/#p141127 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141126/#p141126 Looking at the control board in the video you posted, there is a MOSFET and a power regulator with silver looking tabs.  It looks like they may be touching each other ot something else.  Make sure they don't touch and then see what happens.

-os3dp

]]> Wed, 27 Dec 2017 18:37:42 +0000 https://www.soliforum.com/post/141126/#p141126 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141124/#p141124 I have swapped the power and auto buttons no change

]]> Wed, 27 Dec 2017 18:11:08 +0000 https://www.soliforum.com/post/141124/#p141124 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141123/#p141123 https://photos.app.goo.gl/tIWP6nU0AofUThsG2
https://photos.app.goo.gl/kE5A5b2bRyxvnuGG2

]]> Wed, 27 Dec 2017 18:09:54 +0000 https://www.soliforum.com/post/141123/#p141123 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141121/#p141121 The buttons move left right and Center so I don't know

]]> Wed, 27 Dec 2017 17:18:08 +0000 https://www.soliforum.com/post/141121/#p141121 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141119/#p141119 in manual mode the the knob only controls the speed of the winder unless you are holding a button down. I think you might have a wire crossed if its not controlling the speed

]]> Wed, 27 Dec 2017 17:08:38 +0000 https://www.soliforum.com/post/141119/#p141119 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141117/#p141117 Is the Red laser lit on the sensor?

]]> Wed, 27 Dec 2017 16:55:59 +0000 https://www.soliforum.com/post/141117/#p141117 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141116/#p141116 No but it moves the gide left and right

]]> Wed, 27 Dec 2017 16:54:20 +0000 https://www.soliforum.com/post/141116/#p141116 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141095/#p141095 Delloman,

If you turn the variable knob does the motor get faster and slower?

-os3dp

]]> Tue, 26 Dec 2017 22:29:47 +0000 https://www.soliforum.com/post/141095/#p141095 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141094/#p141094 Spin test* so I flipped the magnet no charge please help I am working with pla and need the winder

]]> Tue, 26 Dec 2017 22:04:08 +0000 https://www.soliforum.com/post/141094/#p141094 <![CDATA[Re: Filawinder always spinning]]> https://www.soliforum.com/post/141057/#p141057 So when I plug the winder in it spins no matter what I do I have checked all the wireing and it checks out only thing I can think is maybe the magnet is backwards? I did the spend test but still could have gotten pulled over would this be a symptom of that?

]]> Tue, 26 Dec 2017 03:33:15 +0000 https://www.soliforum.com/post/141057/#p141057 <![CDATA[Filawinder always spinning]]> https://www.soliforum.com/post/141026/#p141026 I am trying to calibrate the winder but it's always spinning I checked the wireing  and the switch works. I checked it with a meter. I could use some help. I don't know what to try next

]]> Sun, 24 Dec 2017 21:16:41 +0000 https://www.soliforum.com/post/141026/#p141026