<![CDATA[SoliForum - 3D Printing Community — Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/topic/16970/wiring-the-mk2a-to-direct-12v-powersupply/ Wed, 20 Dec 2017 19:11:31 +0000 PunBB <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/post/140883/#p140883 You could wire it just about the same as the filastruder instructions. Just without the motor and stall protection board. heat bed in place of heat band

]]> Wed, 20 Dec 2017 19:11:31 +0000 https://www.soliforum.com/post/140883/#p140883 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/post/140880/#p140880 Hi Tim,

- Like you suggested, I guess the SESTOS D1S-2R-24 should be a good option, over the board I suggested.

- Could you help me with, what the connection diagram would look like? Below are the components I have/intend to buy:
1.  Power Supply 12Vdc
https://www.ebay.com/itm/SUPERNIGHT-12V … 4adebca1da
2.  HeatBed
https://www.ebay.com/i/171996091360?rt=nc
3.  Thermister

Would I need anything else other than wires, to make this run independently?

]]> Wed, 20 Dec 2017 18:27:52 +0000 https://www.soliforum.com/post/140880/#p140880 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/post/140848/#p140848 Looks like it would work . You may need an additional SSR to power the heat bed. Cheap enough assuming you do not need this for critical control and you are not in a rush.
What is your application if I may ask.

]]> Wed, 20 Dec 2017 00:22:23 +0000 https://www.soliforum.com/post/140848/#p140848 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/post/140827/#p140827 Hi there,

- Sorry, I did not notice I did not notice I posted it in the Filastruder Board.

- Would something like the below board work?
https://www.ebay.com/itm/Temperature-Co … 1918997931

]]> Tue, 19 Dec 2017 19:12:46 +0000 https://www.soliforum.com/post/140827/#p140827 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/post/140811/#p140811 the pid controler from filasruder would be a good option

]]> Tue, 19 Dec 2017 11:28:44 +0000 https://www.soliforum.com/post/140811/#p140811 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/post/140810/#p140810 The simplest would probably just jet a ramps bard w/ arduino 2560  and a thermisistor. . Maybe a 2o04 controller board . or just find a good arduino book like the Arduino cook book  it should give I/O info for such a projects.

]]> Tue, 19 Dec 2017 11:27:22 +0000 https://www.soliforum.com/post/140810/#p140810 <![CDATA[Re: Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/post/140809/#p140809 heated bed on a filastruder?

]]> Tue, 19 Dec 2017 11:18:28 +0000 https://www.soliforum.com/post/140809/#p140809 <![CDATA[Wiring the MK2a to direct 12V PowerSupply ??]]> https://www.soliforum.com/post/140807/#p140807 Hey there,

I'm a newbie, trying to figure out if there is a way to wire the MK2a Heatbed directly to a 12V Power Supply. I mean, independent from the 3D Printers control board. What would be the components I need and the wiring/ connections to make?

12V ---------> ??????? ----------> Mk2a /HeatBed

]]> Tue, 19 Dec 2017 07:24:27 +0000 https://www.soliforum.com/post/140807/#p140807