<![CDATA[SoliForum - 3D Printing Community — Solidoodle 4 Board fried?]]> https://www.soliforum.com/topic/16911/solidoodle-4-board-fried/ Thu, 11 Jan 2018 02:26:14 +0000 PunBB <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/141514/#p141514 Not sure, just used the one in the link, even remembered to define the board lol, compiled and uploaded. now end stops are triggered, have to look up what I changed before.

]]> Thu, 11 Jan 2018 02:26:14 +0000 https://www.soliforum.com/post/141514/#p141514 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/141513/#p141513 What version of Marlin is that?
Probably want this one https://github.com/ozadr1an/Solidoodle- … in_v1_beta

]]> Thu, 11 Jan 2018 00:41:18 +0000 https://www.soliforum.com/post/141513/#p141513 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/141512/#p141512 K, the config in Rep host was at park and home at 200 already, so dont think that is the issue.http://soliforum.com/i/?du69C9J.jpg
But while looking in the sketch config, it lists this. Should it be changed to x home pos 200 and y too?

]]> Thu, 11 Jan 2018 00:04:41 +0000 https://www.soliforum.com/post/141512/#p141512 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/141510/#p141510 ok, for some reason I thought home was 0,0 at the right rear. I shall redo the config and see if that helps

]]> Wed, 10 Jan 2018 23:35:11 +0000 https://www.soliforum.com/post/141510/#p141510 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/141508/#p141508 Yep you have endstops that aren’t working. Or you have your printer configuration incorrect within RH.
200,200 is Home on an SD.  That is the right rear of the machine.

]]> Wed, 10 Jan 2018 23:27:46 +0000 https://www.soliforum.com/post/141508/#p141508 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/141507/#p141507 Well after taking alot of time off, Im back to trying to figure things out... So I can manually move x , y , z in Rep, but when I home any of them they go the opposite direction. Any ideas?

]]> Wed, 10 Jan 2018 23:13:46 +0000 https://www.soliforum.com/post/141507/#p141507 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140361/#p140361 Repetier Host comes with cura and slic3r  so they need to be configured as well.

]]> Tue, 05 Dec 2017 00:37:24 +0000 https://www.soliforum.com/post/140361/#p140361 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140360/#p140360 I sort of figured it would run on the old software, since I uploaded the firmware to the mks? So dont use host, just regular repitier?

]]> Mon, 04 Dec 2017 23:26:46 +0000 https://www.soliforum.com/post/140360/#p140360 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140359/#p140359 Why are you using solid print and repitier host.
The driver should be installed with your  your arduino and then just use repiter to run things.

]]> Mon, 04 Dec 2017 23:06:16 +0000 https://www.soliforum.com/post/140359/#p140359 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140358/#p140358 OK new(used) laptop.Previously I compiled and uploaded firmware) Installed soliprint and virtual driver then repetier host. But nothing works, no lights, no fans. http://soliforum.com/i/?rgvNybx.jpghttp://soliforum.com/i/?NjUhURK.jpghttp://soliforum.com/i/?j6qTbb8.jpg

Any clue what I am doing wrong, or did wrong?

]]> Mon, 04 Dec 2017 20:57:41 +0000 https://www.soliforum.com/post/140358/#p140358 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140299/#p140299 Ugh, sorry to hear about the laptop. that stinks.

Hope you get it sorted out soon.

]]> Fri, 01 Dec 2017 13:32:06 +0000 https://www.soliforum.com/post/140299/#p140299 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140295/#p140295 Sorry for the delay, for sure I will post info on how it works out. I had a setback with my laptop a few days ago, the hard drive crapped out on me. So it may be a few more days til I'm back to tinkering with my printer.

]]> Fri, 01 Dec 2017 02:48:42 +0000 https://www.soliforum.com/post/140295/#p140295 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140214/#p140214 no problem. smile 

Please let us know how things go for you with this board. It would be nice to have the info for future users to have another option.

]]> Sun, 26 Nov 2017 15:12:45 +0000 https://www.soliforum.com/post/140214/#p140214 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140154/#p140154 Thank you smile

]]> Sat, 25 Nov 2017 00:30:12 +0000 https://www.soliforum.com/post/140154/#p140154 <![CDATA[Re: Solidoodle 4 Board fried?]]> https://www.soliforum.com/post/140123/#p140123 Here ya go...

https://drive.google.com/open?id=0BzoHq … FlVTkhwWWs

]]> Fri, 24 Nov 2017 03:59:52 +0000 https://www.soliforum.com/post/140123/#p140123