<![CDATA[SoliForum - 3D Printing Community — filastruder only works in reverse GF45 - v2.0]]> https://www.soliforum.com/topic/16863/filastruder-only-works-in-reverse-gf45-v20/ Wed, 01 Nov 2017 15:05:39 +0000 PunBB <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> https://www.soliforum.com/post/139383/#p139383 It looks like the motor has been overloaded, and the stall protection board may not have been set up properly. All motors are tested before shipment.

In the assembly process, there is a step that asks the user to confirm the auger rotates freely by hand. Did it rotate freely then?

Did you add any plastic yet? Hold off on that until the auger is spinning freely.

How did you configure the limit on the stall protection board?

Replacement gears are here:

https://www.filastruder.com/collections … ment-gears

]]> Wed, 01 Nov 2017 15:05:39 +0000 https://www.soliforum.com/post/139383/#p139383 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> https://www.soliforum.com/post/139351/#p139351 http://soliforum.com/i/?226PIy9.jpg

This one has small damage hard to pick up on camera this is  gear 3

]]> Tue, 31 Oct 2017 14:10:36 +0000 https://www.soliforum.com/post/139351/#p139351 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> https://www.soliforum.com/post/139350/#p139350 http://soliforum.com/i/?klrWMnL.jpg

]]> Tue, 31 Oct 2017 14:00:35 +0000 https://www.soliforum.com/post/139350/#p139350 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> https://www.soliforum.com/post/139348/#p139348

I disconnected everything and only used power supply to the mortar still sounds like skipping gears ?

]]> Tue, 31 Oct 2017 13:42:40 +0000 https://www.soliforum.com/post/139348/#p139348 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> https://www.soliforum.com/post/139345/#p139345 A grinding sound indicates that one or more gears are stripped in the gearbox. Would recommend checking the gears. If stripped, we do well replacements. You'll also want to check the stall protection board current limit, as that prevents the gearbox from damaging itself.

In the assembly process, there is a step that asks the user to confirm the auger rotates freely by hand. Did it rotate freely yet?

Did you add any plastic yet? Hold off on that until the auger is spinning freely.

]]> Tue, 31 Oct 2017 13:29:03 +0000 https://www.soliforum.com/post/139345/#p139345 <![CDATA[Re: filastruder only works in reverse GF45 - v2.0]]> https://www.soliforum.com/post/139341/#p139341 you should go through the wiring and make sure its all connected correctly

]]> Tue, 31 Oct 2017 10:25:33 +0000 https://www.soliforum.com/post/139341/#p139341 <![CDATA[filastruder only works in reverse GF45 - v2.0]]> https://www.soliforum.com/post/139328/#p139328 my new filastruder v2.0  only works in reverse if I change the motor cables it just makes a grinding sound doesn't move

5 hours can't work this out sad
things I tried looson the screws
change Stall Protection

thanks

]]> Mon, 30 Oct 2017 23:37:16 +0000 https://www.soliforum.com/post/139328/#p139328