<![CDATA[SoliForum - 3D Printing Community — Davinci v1.0 firmware help!]]> https://www.soliforum.com/topic/16726/davinci-v10-firmware-help/ Fri, 08 Sep 2017 23:56:19 +0000 PunBB <![CDATA[Re: Davinci v1.0 firmware help!]]> https://www.soliforum.com/post/137862/#p137862 evanboothe wrote:
carl_m1968 wrote:

For the 1.0 you can just flash the Firmware to Repetier and use the Repetier host.

I want to do this but cannot find a up to date tutorial

This seems to be pretty much what you are looking for..

http://www.soliforum.com/topic/16731/ho … a-updated/

]]> Fri, 08 Sep 2017 23:56:19 +0000 https://www.soliforum.com/post/137862/#p137862 <![CDATA[Re: Davinci v1.0 firmware help!]]> https://www.soliforum.com/post/137852/#p137852 carl_m1968 wrote:

For the 1.0 you can just flash the Firmware to Repetier and use the Repetier host.

I want to do this but cannot find a up to date tutorial

]]> Fri, 08 Sep 2017 15:57:37 +0000 https://www.soliforum.com/post/137852/#p137852 <![CDATA[Re: Davinci v1.0 firmware help!]]> https://www.soliforum.com/post/137850/#p137850 please try the method described in "[HOWTO] Print after spoll chip run to zero in Jr.1 FW2.3.3" and let us know if it works. it take advantage of a glich discovered in xyzware and may or may not be hardware dependent. i so far have little feedback from people with other model machine except jr. and jr.w, but so far response are positive.

]]> Fri, 08 Sep 2017 13:21:53 +0000 https://www.soliforum.com/post/137850/#p137850 <![CDATA[Re: Davinci v1.0 firmware help!]]> https://www.soliforum.com/post/137849/#p137849 For the 1.0 you can just flash the Firmware to Repetier and use the Repetier host.

]]> Fri, 08 Sep 2017 10:19:57 +0000 https://www.soliforum.com/post/137849/#p137849 <![CDATA[Re: Davinci v1.0 firmware help!]]> https://www.soliforum.com/post/137842/#p137842 So what are my options for 3rd party spools aside from using a different board and having to jump terminals and stuff. There has to be a easier way to fool the chip.. or if I can flash the stock module with differnt firmware.

]]> Fri, 08 Sep 2017 05:08:30 +0000 https://www.soliforum.com/post/137842/#p137842 <![CDATA[Re: Davinci v1.0 firmware help!]]> https://www.soliforum.com/post/137840/#p137840 poomsag wrote:

Please look at [HOWTO] Print after spoll chip run to zero in Jr.1 FW2.3.3 [Updated 9]
You can edit temperature in xyz advance mode.

The JR uses RFID to tead its spools. The 1.0 has an actual 3 wite chip that requires a physical connection at the base of each spool. The 1.0 does not work the same as the JR in regards to spool verification.

]]> Fri, 08 Sep 2017 02:55:28 +0000 https://www.soliforum.com/post/137840/#p137840 <![CDATA[Re: Davinci v1.0 firmware help!]]> https://www.soliforum.com/post/137839/#p137839 Please look at [HOWTO] Print after spoll chip run to zero in Jr.1 FW2.3.3 [Updated 9]
You can edit temperature in xyz advance mode.

]]> Fri, 08 Sep 2017 02:10:55 +0000 https://www.soliforum.com/post/137839/#p137839 <![CDATA[Davinci v1.0 firmware help!]]> https://www.soliforum.com/post/137838/#p137838 Hey guys new here and new to 3D printing! Looking for some help, I don't want to have to run these XYZ based cartridges. I would also like to be able to have more settings for heat control, etc. searched around I have found so much differnt info and I just wanted a LATEST opinion/help, concerning ways to either be able to use differnt spool brands and a possible updated tutorial on how to flash for differnt software. Thanks.

]]> Fri, 08 Sep 2017 01:25:15 +0000 https://www.soliforum.com/post/137838/#p137838