<![CDATA[SoliForum - 3D Printing Community — Custom Figure - Iron Knight]]> https://www.soliforum.com/topic/16397/custom-figure-iron-knight/ Fri, 05 May 2017 00:09:10 +0000 PunBB <![CDATA[Re: Custom Figure - Iron Knight]]> https://www.soliforum.com/post/135171/#p135171 ...aaaaand an itty bitty kitty face :3

http://i.imgur.com/sDEdTqb.jpg

http://i.imgur.com/2CeVnEP.jpg

I finally managed to find the .1 mm setting.

]]> Fri, 05 May 2017 00:09:10 +0000 https://www.soliforum.com/post/135171/#p135171 <![CDATA[Re: Custom Figure - Iron Knight]]> https://www.soliforum.com/post/135131/#p135131 Added some pauldrons:

http://i.imgur.com/HfAsDnF.jpg

]]> Wed, 03 May 2017 22:30:45 +0000 https://www.soliforum.com/post/135131/#p135131 <![CDATA[Re: Custom Figure - Iron Knight]]> https://www.soliforum.com/post/135035/#p135035 Blender intimidated me for over four years until I finally bit the bullet.  Now I use it nearly everyday.  You can't go wrong with free stuff.

Torso came out well.  Glued the two haves together with a gluestick and did a bit of coloring with sharpie.  Might make another version with the two colors separated- easier to spraypaint.

http://i.imgur.com/YIGusEA.jpg
Back side doesn't show up very well on camera hmm

Cut the legs up into these little pieces: they're currently printing.  Decided against articulated joints until I can find a good base to work off.

http://i.imgur.com/cotj04A.png

edit: leg bits printed and assembled... ish.  Being held together with wall putty XD

http://i.imgur.com/fmgukGA.jpg

]]> Sun, 30 Apr 2017 19:31:33 +0000 https://www.soliforum.com/post/135035/#p135035 <![CDATA[Re: Custom Figure - Iron Knight]]> https://www.soliforum.com/post/135028/#p135028 Neat! look forward to seeing the prints. smile


knowack wrote:

What software is that screenshot?

Definitely Blender, =P

]]> Sun, 30 Apr 2017 17:02:08 +0000 https://www.soliforum.com/post/135028/#p135028 <![CDATA[Re: Custom Figure - Iron Knight]]> https://www.soliforum.com/post/135023/#p135023 knowack wrote:

What software is that screenshot?

That's Blender.

OP- looks great

]]> Sun, 30 Apr 2017 03:30:49 +0000 https://www.soliforum.com/post/135023/#p135023 <![CDATA[Re: Custom Figure - Iron Knight]]> https://www.soliforum.com/post/135021/#p135021 What software is that screenshot?

]]> Sun, 30 Apr 2017 01:20:36 +0000 https://www.soliforum.com/post/135021/#p135021 <![CDATA[Re: Custom Figure - Iron Knight]]> https://www.soliforum.com/post/135017/#p135017 looks good

]]> Sat, 29 Apr 2017 15:30:53 +0000 https://www.soliforum.com/post/135017/#p135017 <![CDATA[Custom Figure - Iron Knight]]> https://www.soliforum.com/post/135016/#p135016 So, being the goob that I am, I am transforming a 3d model I use in my webcomic (http://everett.webcomic.ws/blog)into a figure via the Davinci Jr.

I have to trace over the original as I didn't make it watertight, while I'm at it I'll have to decide what sort of joint system I'll be using (if any)  Estimated height 6".

http://i.imgur.com/olnqzvh.png

Already printed a logo sort of thing -my first print after a few presets.  Accidentally used spray-on rubber instead of spraypaint XD

http://i.imgur.com/MnGYyeb.jpg

]]> Sat, 29 Apr 2017 15:27:28 +0000 https://www.soliforum.com/post/135016/#p135016