<![CDATA[SoliForum - 3D Printing Community — stall protection]]> https://www.soliforum.com/topic/16281/stall-protection/ Tue, 28 Mar 2017 16:19:58 +0000 PunBB <![CDATA[Re: stall protection]]> https://www.soliforum.com/post/134071/#p134071

A heatsink is not needed, but one is included in the kit.

 
good to know thanks elmoret. Am being tortured by tracking!! my struder somewhere between Miami and the Atlantic.

]]> Tue, 28 Mar 2017 16:19:58 +0000 https://www.soliforum.com/post/134071/#p134071 <![CDATA[Re: stall protection]]> https://www.soliforum.com/post/134065/#p134065 A heatsink is not needed, but one is included in the kit.

]]> Tue, 28 Mar 2017 13:56:09 +0000 https://www.soliforum.com/post/134065/#p134065 <![CDATA[Re: stall protection]]> https://www.soliforum.com/post/134057/#p134057

the input side has the 12v supply soldered and the fan wired to the terminals

lol middle of the night clicked to that what you may have meant.  I've decided to settle on desoldering the terminal blocks and moving it across and adding another.

I seen in a Ytube vid someone adding heatsink to the fet, but they dont mention dimensions , wondering if someone knows  even an ebay link be helpful... not 100% its needed else  it be in the kit, but for what they cost it want harm things having it.

]]> Tue, 28 Mar 2017 08:11:59 +0000 https://www.soliforum.com/post/134057/#p134057 <![CDATA[Re: stall protection]]> https://www.soliforum.com/post/134056/#p134056 Sorry you are correct, the input side has the 12v supply soldered and the fan wired to the terminals

]]> Tue, 28 Mar 2017 07:22:06 +0000 https://www.soliforum.com/post/134056/#p134056 <![CDATA[Re: stall protection]]> https://www.soliforum.com/post/134038/#p134038 The only load on the out side should be the gearmotor, not the fan.

]]> Mon, 27 Mar 2017 14:28:41 +0000 https://www.soliforum.com/post/134038/#p134038 <![CDATA[Re: stall protection]]> https://www.soliforum.com/post/134034/#p134034 ello
Smow did consider soldering directly to the board, but being a first time user "expecting a few tear downs along the way"  so opting for single headers.

with you mentioning the motors, you have your fan connected to the output side of SPB. just from the wiring diagram I get the impression its plugged into the IN side. would/does it make a difference to the setup?

]]> Mon, 27 Mar 2017 10:33:35 +0000 https://www.soliforum.com/post/134034/#p134034 <![CDATA[Re: stall protection]]> https://www.soliforum.com/post/134029/#p134029 I did something similar, I soldered the motor to the pos neg pads and ran the fan into the terminals. I figured soldering was better than screw down terminals for the motor

]]> Mon, 27 Mar 2017 09:43:53 +0000 https://www.soliforum.com/post/134029/#p134029 <![CDATA[stall protection]]> https://www.soliforum.com/post/134028/#p134028 hello.
while am waiting for a filastruder am slowly digesting the manual but wondering about the fan being wired to the SPB " stall protection board" rather than cramming the motor fan wiring into the terminal.
http://soliforum.com/i/?CykVKbH.jpg

could I just use the +- pads next to the terminal on the IN side of the SPB.

]]> Mon, 27 Mar 2017 09:15:29 +0000 https://www.soliforum.com/post/134028/#p134028