<![CDATA[SoliForum - 3D Printing Community — Extruder gets clogged constantly, help please]]> https://www.soliforum.com/topic/15820/extruder-gets-clogged-constantly-help-please/ Sat, 10 Dec 2016 15:53:09 +0000 PunBB <![CDATA[Re: Extruder gets clogged constantly, help please]]> https://www.soliforum.com/post/128994/#p128994 Well i think the problme is solved, i clenaed the entire hotend (again) and tightened strong and now it works fine.
Thank you so much for you answers!!!!!

]]> Sat, 10 Dec 2016 15:53:09 +0000 https://www.soliforum.com/post/128994/#p128994 <![CDATA[Re: Extruder gets clogged constantly, help please]]> https://www.soliforum.com/post/128944/#p128944 Is comming out of every hole, the resistor hole, the thermistor hole over the heater block and over the noozle

]]> Fri, 09 Dec 2016 21:19:24 +0000 https://www.soliforum.com/post/128944/#p128944 <![CDATA[Re: Extruder gets clogged constantly, help please]]> https://www.soliforum.com/post/128943/#p128943 Is the plastic coming out of the top or bottom of the heater block?

]]> Fri, 09 Dec 2016 21:01:55 +0000 https://www.soliforum.com/post/128943/#p128943 <![CDATA[Re: Extruder gets clogged constantly, help please]]> https://www.soliforum.com/post/128934/#p128934 the overflow is getting worse and now the plastic is getting inside the thermistor hole and cheats the readings any siggestion what this could be?

]]> Fri, 09 Dec 2016 15:44:14 +0000 https://www.soliforum.com/post/128934/#p128934 <![CDATA[Re: Extruder gets clogged constantly, help please]]> https://www.soliforum.com/post/128922/#p128922 ok so here is the thing i chanched the thermistor to see if the temp is correct and with the other thermistor the temp marked is 165 degrees when i set it to 190 in pronterface, because of that i raise it to 220 in pronterface and the thermistor marks 190 the fan on and it seeems to print but it overflows everywhere i ve attached a video but the quiality is very poor sorry for that

https://youtu.be/wEIJ4KAi_0I

any suggestions for the oveflow?

]]> Fri, 09 Dec 2016 12:55:03 +0000 https://www.soliforum.com/post/128922/#p128922 <![CDATA[Re: Extruder gets clogged constantly, help please]]> https://www.soliforum.com/post/128920/#p128920 Thank for the answer. The acetone does not disolve the PLA but its easier to remove after a couple of hours in acetone. I use the acetone to soften the PLA and it works pretty well, i remove remains with torch ass yo say. The brand of the PLA is fillamentum 2.85mm and i ve changed to higher temps but still clogging. I have not tried different brand because it worked very good with te first pieces and now just don t. And that is what i can not undertand.

]]> Fri, 09 Dec 2016 12:38:02 +0000 https://www.soliforum.com/post/128920/#p128920 <![CDATA[Re: Extruder gets clogged constantly, help please]]> https://www.soliforum.com/post/128919/#p128919 PLA cannot be dissolved by acetone.  It only works for  ABS. The people that did have clogs usually burned it out using a torch on the metal parts only.  You can also try to master the cold pull method but good luck on that. Google it for more info. What brand filament are you using?  Have you tried higher temps. Have you tried a different brand?

]]> Fri, 09 Dec 2016 12:25:18 +0000 https://www.soliforum.com/post/128919/#p128919 <![CDATA[Extruder gets clogged constantly, help please]]> https://www.soliforum.com/post/128918/#p128918 Hello everyone i ve got a really anoying problem and i just dont know what else to do. I ve got a prusa i3 and printed successfull 10 pieces aprox. and any problem untill a couple of days ago, the extruder gets clogged constantly y can t print anything at all. The parts i printed so far were printed with PLA, 190 degrees with the fan in automatic using Slic3r. I ve dismantle the entire Hotend twice and gave the parts an acetone bath for two nights but nothing, it stills heting jammed. I would apreciate the help so much. If you need any detail feel freeto ask.

thanks

]]> Fri, 09 Dec 2016 11:43:16 +0000 https://www.soliforum.com/post/128918/#p128918