<![CDATA[SoliForum - 3D Printing Community — practice gun]]> https://www.soliforum.com/topic/1575/practice-gun/ Fri, 08 Mar 2013 05:05:52 +0000 PunBB <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15505/#p15505 So, I guess the 7.62x39 upper I have is out of the question wink I still haven't even tried it on a 22... been bogged down with other work but I was thinking a 9mm upper would probably work as well plus I have a couple of 5.7x28 uppers here I might try out when time permits they don't have much recoil but they use a different system for the buffer so might be worse....

]]> Fri, 08 Mar 2013 05:05:52 +0000 https://www.soliforum.com/post/15505/#p15505 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15492/#p15492 Peek-A-View...hahaha

couple notes for all the printed gun people. 

1. Printed lower in ABS works fine as long as you dont set it up with a .223 upper (stick to a .22 upper)

2. I think if you could print one out of Taulman 618 it would easily hold up to 1000+ rnds of .223

]]> Fri, 08 Mar 2013 03:16:24 +0000 https://www.soliforum.com/post/15492/#p15492 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15429/#p15429 well here is the assembled piece

the trigger guard broke so i had take it off but it should work

]]> Thu, 07 Mar 2013 20:02:06 +0000 https://www.soliforum.com/post/15429/#p15429 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15332/#p15332 one of the lowers was but it only went 88 rounds before they broke it

ok i'm posting a new stl for a 3 part practice gun i've included an area to add weights. The new design works with the handle for a ar15 lower and is only partially based off of an ar 15 lower these should print a little better and be able to be glued together with just a little bit of work

]]> Thu, 07 Mar 2013 02:23:56 +0000 https://www.soliforum.com/post/15332/#p15332 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15244/#p15244 Damn, I thought I read somewhere that the latest lower was fdm.

]]> Wed, 06 Mar 2013 17:25:40 +0000 https://www.soliforum.com/post/15244/#p15244 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15211/#p15211 thats a cool vid havent seen that one yet

]]> Wed, 06 Mar 2013 11:16:20 +0000 https://www.soliforum.com/post/15211/#p15211 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15191/#p15191 att he end of the vid there is an fdm lower beign printed however that lower only fired 88 rounds before there was an unrelated mechanical problem to the upper. they attempted the stupid way of clearing the problem by beating the butt of the gun on the ground and cracked the lower tower renderign the lower and firearm un servicable

sorry i reread and had to correct the problem was in the upper not the lower as previously indicated. I've talked with several of the peopel involved in the project at defcad.org in the chatroom. they doe stimate the SLA upper would have worked for over 1000 rounds but they ran our of ammo.

we ran a cost analysis on it and a printed abs lower at a 60% infill would cost $4.41 if the abs was $42 per kg and you could print approximately 10.6 units per kg

]]> Wed, 06 Mar 2013 04:39:43 +0000 https://www.soliforum.com/post/15191/#p15191 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15190/#p15190 It's not?? Near the end of this vid, that's not fdm?

http://defcad.org/defdist-ar-15-lower-receiver/

]]> Wed, 06 Mar 2013 04:32:05 +0000 https://www.soliforum.com/post/15190/#p15190 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15165/#p15165 creation the 600 rndr was an sla lower not an FDM lower the FDM lower broke at the tower

]]> Tue, 05 Mar 2013 23:06:15 +0000 https://www.soliforum.com/post/15165/#p15165 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15122/#p15122 I agree with splitting it in the middle and printing both halves and gluing it together.
I too also want to try the AR15 lower, but i'm waiting on the release of the .stl for the latest version of it. Over 600 rounds with no issues, that's nuts! I want a bright green lower at the range! Get the good 'ol boys saying, "what the hell" with that crazy southern accent.

]]> Tue, 05 Mar 2013 17:55:52 +0000 https://www.soliforum.com/post/15122/#p15122 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15092/#p15092 looks cool man want to try the ar-15 reciever print when i get my printer

]]> Tue, 05 Mar 2013 11:09:31 +0000 https://www.soliforum.com/post/15092/#p15092 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15045/#p15045 The first one looked good... Might want to think about enclosing your build area...
Also, cutting it in half long ways, printing both halves and gluing them together sounds like a really good idea.

]]> Mon, 04 Mar 2013 21:53:58 +0000 https://www.soliforum.com/post/15045/#p15045 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/15006/#p15006 Well here are the pics of my fucked up print

]]> Mon, 04 Mar 2013 18:17:30 +0000 https://www.soliforum.com/post/15006/#p15006 <![CDATA[Re: practice gun]]> https://www.soliforum.com/post/14957/#p14957 cut it in half on the horizontal (with netfab free for example) ... it will print better with less risk of warping and you didn't need support , so you will get a better look... you just need to glue the two parts after that..

]]> Mon, 04 Mar 2013 10:50:38 +0000 https://www.soliforum.com/post/14957/#p14957 <![CDATA[practice gun]]> https://www.soliforum.com/post/14936/#p14936 I was asked by my brother if i could print a practice gun using some of the files iv' eammased i took a frame and worked this up. Currently i'm printing it at 3mm with a raft and suppro tmatterial print time is about 8 hours and this is approximately 2 hours into the print

i am currently seeing some lift on the barrel end i've been avused i should have used soem abs glue shrug we'll worry about this alter however

Personally i think if i build an encliosure to retain heatit would be far better than glue

]]> Mon, 04 Mar 2013 05:20:41 +0000 https://www.soliforum.com/post/14936/#p14936