SoliForum - 3D Printing Community — Finally solved all my issues.

Re: Finally solved all my issues.

null@example.com (rrssll) — Thu, 02 Feb 2017 06:41:32 +0000

Fwiw the mods I copied from MacGyverX are the best part of the best parts of my Press. Just tonight I finally finished installing the heated bed upgrade he recommended. The parts sat for a year and I have a Prusa i3 on the way in a few weeks but I'm still glad I did it. And the hotend mod was a major improvement over stock. It's the only reason I got any decent prints out of the machine.

Thanks for your tireless contributions MacGyverX.

Re: Finally solved all my issues.

null@example.com (Tin Falcon) — Wed, 25 Jan 2017 11:41:16 +0000

A flawed setup

IMHO most if not all hobby level 3d printers will be flawed. MY I 3 has junk for z axis rods .......

This hobby is about buying the best one can afford and the best deal of the day and learning to make it work,
Unfortunately the "plug and play machines" are not necessary easier to use but are harder to upgrade /mod / repair.
Tin

Re: Finally solved all my issues.

null@example.com (knowack) — Wed, 25 Jan 2017 05:29:03 +0000

MacGyverX wrote:

'but very flawed setup.'
Thanks.

I'm sure he meant it in the nicest possible way.

Re: Finally solved all my issues.

null@example.com (MacGyverX) — Wed, 25 Jan 2017 04:19:36 +0000

'but very flawed setup.'

Thanks.

Re: Finally solved all my issues.

null@example.com (AOYOU3D) — Wed, 21 Dec 2016 21:54:58 +0000

I left this message in the another topic section, also may remind you that
it is not worth to spend money and time on a SD press printer, it
is failing design, so better to buy a simple Prusa i3($200-300) instead of
upgrading SD press.

"For SD press printer, I am just indicating a terrible design:
There are no any metal or engineering plastic bushings
on X, Y, Z carriages, just made holes on the general plastic
such as ABS or similar one that only used for enclosure or
box.
They have very different friction coefficient, wear strength
and heat transfer property between the engineering plastic bushings
and the general plastic, so these holes on the plastic carriages
wear out quickly, do you like to replace those carriages?
So I think it is not worth to spend money and time on SD press."

I don't like to discuss other issues, I didn't see any good prints that made
by SD press, maybe there are few pieces, but few thousands failing
SD press printers in the current market.

Are you able to print these objects that I designed and made by a simple Prusa i3?

Re: Finally solved all my issues.

null@example.com (daphur) — Sun, 04 Sep 2016 00:33:21 +0000

You have a shot of the risers?

Re: Finally solved all my issues.

null@example.com (mrallinwonder) — Sun, 21 Aug 2016 16:52:57 +0000

thanx, i'll try lid closed. I have it open for a cable holder that sits up high over the middle of the printer.

Re: Finally solved all my issues.

null@example.com (seven2099) — Sat, 20 Aug 2016 05:59:53 +0000

that's most likely due one of these factors:

- voltage calibration for each of the axis: fixes a load of print quality issues
- print temperature / too low/high or drafts if you print with the top is open
- print speed (critical)
- retraction (in some sense)

I still have some minor delamination happening here and there, but for the most part I can produce some clean parts if i go at 50-100% speed. At 200% speed and above, i get a lot of pooling in sharp angles but all of it can be sanded down.

Hope that helps

Re: Finally solved all my issues.

null@example.com (mrallinwonder) — Fri, 19 Aug 2016 15:33:00 +0000

Nice work. I have a lot of mods too, but if I print an object over 1.5" high, it always delaminates in the high parts.
Did any particular mod clear that problem for you?

Finally solved all my issues.

null@example.com (seven2099) — Fri, 19 Aug 2016 01:14:19 +0000

I can finally say I have solved all my issues with the Press.

What a rocky road on such a lemon of a printer:

Please see the mods below

e3dv6
bowden aluminum setup
PEI print bed
Printbed Risers added to level
CASE MODS GALORE

Please see pics

and now 20 hour print without the terrible issues with the bowden setup that was recommended by MacGyverX. I thank him for his effort but very flawed setup. The PTFE tube kept coming out because of the constant friction on the tubing. Also the print bed couldn't be leveled and now I've finally solved it by installing some risers and using a 3 way level.

Fine tuned repetier, now i print at 300% speed and going like a speed demon.