<![CDATA[SoliForum - 3D Printing Community — wrong axis movements]]> https://www.soliforum.com/topic/15362/wrong-axis-movements/ Sun, 14 Aug 2016 14:19:11 +0000 PunBB <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126232/#p126232 Unpredictable is a understatement lol. Is there anything else to get sharper corners?

]]> Sun, 14 Aug 2016 14:19:11 +0000 https://www.soliforum.com/post/126232/#p126232 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126230/#p126230 The belts may be a little too tight now .
And increase the vref  a bit.
adjusting pots can take a little time . and they can be unpredictable.
in my slic3r settings acceleration is set for 1000 mm/sec^2
so probably .

]]> Sun, 14 Aug 2016 13:58:35 +0000 https://www.soliforum.com/post/126230/#p126230 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126228/#p126228 Sigh i've run into another problem. I was trying to clean my corners to get sharper prints and dialed in extrusion rate and noticed both y belts are loose I tightened them and now when making quick moves it binds and causes skipping.  I dialed the max acceleration back to 3000 should I go back even further?  I also got the ripples to go away but sporadically I get clicking.

]]> Sun, 14 Aug 2016 13:37:45 +0000 https://www.soliforum.com/post/126228/#p126228 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126225/#p126225

Using up causes the bed to move down

As it should be  sounds like you have it sorted out.
Tin .

]]> Sun, 14 Aug 2016 12:15:10 +0000 https://www.soliforum.com/post/126225/#p126225 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126220/#p126220 Using up causes the bed to move down.   So far everything is good now. The manual home position was different from what rh was reporting.

]]> Sun, 14 Aug 2016 02:29:08 +0000 https://www.soliforum.com/post/126220/#p126220 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126217/#p126217

So wired endstop as no. Everything moves correctly. However, when I click move to 10mm in rh it moves to 10 and when I issue G1 Z11 it moves backwards ?  X and y move to the correct location when issuing the same gcode command.

OK I have to ask in RH  are you using the arrow above or below  the circle and when you do the g1 Z11 comand does the bed move up or down.

]]> Sun, 14 Aug 2016 00:30:12 +0000 https://www.soliforum.com/post/126217/#p126217 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126216/#p126216 sounds like the firmware and software settings  for bed do not match.

]]> Sun, 14 Aug 2016 00:07:37 +0000 https://www.soliforum.com/post/126216/#p126216 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126215/#p126215 Ok I think I found the solution sitting right in front of me  in the firmware I don't know why but manual home position was enable and z was set for 150 I changed it to 0 and now everything seems to function as normal. Thanks a lot you guys.

]]> Sat, 13 Aug 2016 23:56:33 +0000 https://www.soliforum.com/post/126215/#p126215 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126213/#p126213 So wired endstop as no. Everything moves correctly. However, when I click move to 10mm in rh it moves to 10 and when I issue G1 Z11 it moves backwards ?  X and y move to the correct location when issuing the same gcode command.

I see what's going on now but have no clue how this happened. In rh it says 40 but on the smart lcd it shows placement of 190 that would explain why when I manually issue a gcode movement it goes the other way.

]]> Sat, 13 Aug 2016 23:05:15 +0000 https://www.soliforum.com/post/126213/#p126213 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126199/#p126199 There's your problem

]]> Sat, 13 Aug 2016 20:05:02 +0000 https://www.soliforum.com/post/126199/#p126199 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126198/#p126198 Now that I think about it the switch is wired no instead of nc.

]]> Sat, 13 Aug 2016 19:54:18 +0000 https://www.soliforum.com/post/126198/#p126198 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126194/#p126194 Remember they are open when triggere. Not closed like you'd think.

]]> Sat, 13 Aug 2016 17:19:11 +0000 https://www.soliforum.com/post/126194/#p126194 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126189/#p126189 I have one from open builds will replace and report back.

]]> Sat, 13 Aug 2016 15:59:23 +0000 https://www.soliforum.com/post/126189/#p126189 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126188/#p126188 you do realize to lower the bed you need to tell it t move up?? 
in cnc everything is relative to the tool Ie extruder 

Sounds like inverted logic in the operator controller.

Tin

]]> Sat, 13 Aug 2016 15:58:41 +0000 https://www.soliforum.com/post/126188/#p126188 <![CDATA[Re: wrong axis movements]]> https://www.soliforum.com/post/126187/#p126187 It's sounding more and more like you just need to replace the endstop.
If you are positive the tab and button are being engaged, grab a new one.
http://www.printitindustries.com/collec … /end-stops

They are cheap, so pick up a few...it's nice to have extras smile

]]> Sat, 13 Aug 2016 15:57:03 +0000 https://www.soliforum.com/post/126187/#p126187