<![CDATA[SoliForum - 3D Printing Community — Greetings]]> https://www.soliforum.com/topic/15243/greetings/ Mon, 01 Aug 2016 08:48:54 +0000 PunBB <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125696/#p125696 Thanks Tin.

Thought the Znnn would indicate move the Z axis by whatever is specified. tested it, but it did not do what i was hoping.

Ill research some more, and maybe post a new topic should i still need to.

]]> Mon, 01 Aug 2016 08:48:54 +0000 https://www.soliforum.com/post/125696/#p125696 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125593/#p125593 G 0 is a rapid move

G1 is a normal move so not Z offset.

Z offset can easily be set in slicer via the advanced setting  menu but that may not help you.

]]> Fri, 29 Jul 2016 22:26:13 +0000 https://www.soliforum.com/post/125593/#p125593 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125585/#p125585 sorry, I dont use Z lift, or any other "extra" codes, so I have no clue.
My start g-code is very simple. hmm

Hopefully someone else can answer that question for you.

]]> Fri, 29 Jul 2016 11:34:52 +0000 https://www.soliforum.com/post/125585/#p125585 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125575/#p125575 Oh wait, G1 Znnn might be it?

or am i totally in the wrong parameter section???

]]> Fri, 29 Jul 2016 05:24:35 +0000 https://www.soliforum.com/post/125575/#p125575 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125574/#p125574 Cool, thanks H.

that is quite a list of codes, but seems fairly straight forward.

So to lift the print head in the beginning of the print, should i look at anything that has to do with z offset? if you dont mind me asking? Although i only see codes involving a probe, not sure if that would be it.

]]> Fri, 29 Jul 2016 05:20:30 +0000 https://www.soliforum.com/post/125574/#p125574 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125555/#p125555 hello, Zillard smile

Here is a link to the RepRap Wiki page for G-code (also includes M-codes). I refer to it frequently to verify specific codes - great resource to have handy.

http://reprap.org/wiki/G-code

Good luck with your DaVinci upgrades.

]]> Thu, 28 Jul 2016 11:57:42 +0000 https://www.soliforum.com/post/125555/#p125555 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125554/#p125554 Awesome, ill go look for that.

Thanks much Tin:-)

]]> Thu, 28 Jul 2016 10:59:37 +0000 https://www.soliforum.com/post/125554/#p125554 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125553/#p125553 Thee davinci can be a capable machine
lot of folks here have upgraded the board

There is  a reprap g code cheat sheet on Thiniverse  and a couple other places will give you most of what you need to know about g code . M codes are handy for  troubleshooting and tweaking at times
An Welcome!!
Tin

]]> Thu, 28 Jul 2016 10:22:20 +0000 https://www.soliforum.com/post/125553/#p125553 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125546/#p125546 All good, thanks guys.

Yes i do own one, Da Vinci Jr.

Was on a huge special so kind of an impulse buy, now im fidgeting with it to make it work properly. But so far im looking at buying a new controller and use that instead of messing around with XYZ's bs board with its chipped filament requirements and crappy slicer software.

And i need to learn gcode asap.

But other than that im quite looking forward to getting into 3D printing and actually prototyping some of my designs/ideas i have. So far its a lot of fun.

Looking forward to pick your brains in the near future.

]]> Thu, 28 Jul 2016 06:19:35 +0000 https://www.soliforum.com/post/125546/#p125546 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125536/#p125536 It is summer time sometimes take a while to get responses. people have jobs and lives.  This is a helpful group.

Tin

]]> Wed, 27 Jul 2016 21:52:28 +0000 https://www.soliforum.com/post/125536/#p125536 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125533/#p125533 welcome aboard

]]> Wed, 27 Jul 2016 20:13:32 +0000 https://www.soliforum.com/post/125533/#p125533 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125530/#p125530 Welcome!
Do you own a printer yet? If so, which one?

]]> Wed, 27 Jul 2016 16:37:52 +0000 https://www.soliforum.com/post/125530/#p125530 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125527/#p125527 Give it time, mornings can be a little quiet around here.

]]> Wed, 27 Jul 2016 13:53:31 +0000 https://www.soliforum.com/post/125527/#p125527 <![CDATA[Re: Greetings]]> https://www.soliforum.com/post/125524/#p125524 What a welcome!

]]> Wed, 27 Jul 2016 12:24:27 +0000 https://www.soliforum.com/post/125524/#p125524 <![CDATA[Greetings]]> https://www.soliforum.com/post/125494/#p125494 Hi guys

New to the forum and to 3D printing in general.

Looking forward to learning a lot from all of you, as well as share any experience i might have.

Thank you
Z

]]> Tue, 26 Jul 2016 11:24:35 +0000 https://www.soliforum.com/post/125494/#p125494