<![CDATA[SoliForum - 3D Printing Community — My workspace]]> https://www.soliforum.com/topic/150/my-workspace/ Fri, 21 Sep 2012 15:49:09 +0000 PunBB <![CDATA[Re: My workspace]]> https://www.soliforum.com/post/1480/#p1480 My yellow wire is not hooked up at all...  I think that is a sensor wire to detect the fan's RPM

There is also a speed setting on the antec fan, you could try that switch, but it sounds like it might be bad or maybe the polarity is wrong.

]]> Fri, 21 Sep 2012 15:49:09 +0000 https://www.soliforum.com/post/1480/#p1480 <![CDATA[Re: My workspace]]> https://www.soliforum.com/post/1453/#p1453 How did you wire the fan?  I have a 12v 1 amp adapter I have been using to run a 40mm fan for the extruder, and sometimes a 120mm fan for the back.  I just soldered a couple of headers onto the wires, heat shrinked them and stuck them into the connectors for the black and red wires on the fans.

I can't get this Antec fan to run that way.  The LEDs will turn on, but I can't get the fan to spin.  Does something need to be connected to the yellow wire on the fan?

]]> Thu, 20 Sep 2012 18:35:24 +0000 https://www.soliforum.com/post/1453/#p1453 <![CDATA[Re: My workspace]]> https://www.soliforum.com/post/1372/#p1372 I happened to have a DC power supply for powering an external hard drive laying around from another project.

]]> Mon, 17 Sep 2012 02:08:55 +0000 https://www.soliforum.com/post/1372/#p1372 <![CDATA[Re: My workspace]]> https://www.soliforum.com/post/1371/#p1371 I just ordered one of those Antec fans.  How did you power it?

]]> Sun, 16 Sep 2012 16:02:11 +0000 https://www.soliforum.com/post/1371/#p1371 <![CDATA[Re: My workspace]]> https://www.soliforum.com/post/932/#p932 Inside my house it's pretty good most of the year... I suspect I'll take the spools off and put them in a tub like you suggested if its sticky out.

It only takes a second to take them on and off anyhow

]]> Sun, 02 Sep 2012 17:07:10 +0000 https://www.soliforum.com/post/932/#p932 <![CDATA[Re: My workspace]]> https://www.soliforum.com/post/915/#p915 Nice setup man! The fan and the kill switch look like a great idea. I'm gonna have to do something like this. Is the humidity bad in your area? Here in virginia this summer its been pretty humid. I've been thinking of getting a reusable silica gel dehumidifer and a cheap hydrometer to throw in the tuber-ware container that I'll be storing all my plastic in. I'm not sure if its worth it though.

]]> Sun, 02 Sep 2012 16:35:50 +0000 https://www.soliforum.com/post/915/#p915 <![CDATA[My workspace]]> https://www.soliforum.com/post/906/#p906 I wanted to share my spool holder and workspace setup here

http://i1049.photobucket.com/albums/s383/zimmer62/solidoodle/568c923c.jpg

It's a couple of closet shelf/rod brackets, 3/4 PVC

I have another piece of PVC wedged near the wall at the bottom of the bracket, I'm going to eyehooks in it at each spot for each spool

The filament feeds nicely behind that, and threaded through a hole in the right of the tool holder I have mounted, then into the printer

http://i1049.photobucket.com/albums/s383/zimmer62/solidoodle/70436e37.jpg

http://i1049.photobucket.com/albums/s383/zimmer62/solidoodle/9cde3070.jpg
Kill switch

http://i1049.photobucket.com/albums/s383/zimmer62/solidoodle/aaefa213.jpg
Antec fan from amazon mounted to provide cooling to the board

http://i1049.photobucket.com/albums/s383/zimmer62/solidoodle/8ceb2937.jpg

]]> Sun, 02 Sep 2012 14:03:24 +0000 https://www.soliforum.com/post/906/#p906