<![CDATA[SoliForum - 3D Printing Community — Y axis not responding and loose belts]]> https://www.soliforum.com/topic/14896/y-axis-not-responding-and-loose-belts/ Mon, 10 Oct 2016 04:56:28 +0000 PunBB <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/127469/#p127469 So, to sum, depressing the Y-Axis endstop still sends a signal and reading that it is TRIGGERED.

Also, I do not have loose belts. big_smile

]]> Mon, 10 Oct 2016 04:56:28 +0000 https://www.soliforum.com/post/127469/#p127469 <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/127468/#p127468 Alright, sorry guys, had a busy weekend (20 pages of calculations due, woo!).

I just gave this all a try

Here is what happened:

I sent the M119 command while all where home, I received:

x_max: TRIGGERED
y_max: TRIGGERED
z_max: TRIGGERED

Then, I tried what heartless suggested, and moved each individual carriage into the center and sent the Z-axis down.

I then ran the M119 command again and sent the X and Z home, since I know those work. They gave me a TRIGGERED again, but the y_max was still open. (Again, hitting Y-home just gives me a flicker on the light but no movement).

I did move the Y-Motor a little during the movement of the other carriage on accident and felt resistance, so I know it has power and is working.

]]> Mon, 10 Oct 2016 04:55:02 +0000 https://www.soliforum.com/post/127468/#p127468 <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/127366/#p127366 along the top of RH is a "Toggle Log" - click on that to enable the log report at the bottom

with the carriages away from the endstops, send the M119 command and it will give a status report of the endstops

then, send one axis at a time to the "home" position (start with the 2 axis that are working correctly) and after each one is homed, again send the M119 command to get a status report.

Alternatively, you can manually depress each endstop in turn and send the command to get a status report. (hold it until after the command reports status)

]]> Thu, 06 Oct 2016 11:52:14 +0000 https://www.soliforum.com/post/127366/#p127366 <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/127364/#p127364 Yep then do it again while holding each end stop down  one at a time  see if the states change.

]]> Thu, 06 Oct 2016 10:21:54 +0000 https://www.soliforum.com/post/127364/#p127364 <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/127362/#p127362 In the G-code command line enter M119 and read the output log to see what the endstops are reporting.
All on the manual control panel in RH

]]> Thu, 06 Oct 2016 03:20:24 +0000 https://www.soliforum.com/post/127362/#p127362 <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/127361/#p127361 Sorry Kronik, very nooby here. So, I'm using repetier, move the Y-axis manually to the stop itself, and then do what?

]]> Thu, 06 Oct 2016 03:14:40 +0000 https://www.soliforum.com/post/127361/#p127361 <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/127359/#p127359 engage the endstops and try M119 see what the status of the endstops are

]]> Thu, 06 Oct 2016 01:31:46 +0000 https://www.soliforum.com/post/127359/#p127359 <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/127357/#p127357 Going to bump this one, and maybe get some help from wardjr too.

I have the same issue now occurring. In a previous post I talked about my heatbed giving out. I fixed that issue by replacing the plug that is located just North of the Solidoodle logo on the board. Now, I have no Y-Response. When sending the Y-Axis home, I get a slight flicker in the machine and nothing. It will bunch up commands but never give me anything.

I checked the y-end stop plug located left of the Solidoodle Logo on the CB (Solidoodle 3) and it is perfectly fine, wires don't look damaged. Looks good. What could I be missing?

]]> Thu, 06 Oct 2016 01:21:21 +0000 https://www.soliforum.com/post/127357/#p127357 <![CDATA[Re: Y axis not responding and loose belts]]> https://www.soliforum.com/post/123673/#p123673 Your y endstop is not plugged in or otherwise has a bad connection.

]]> Thu, 02 Jun 2016 22:13:07 +0000 https://www.soliforum.com/post/123673/#p123673 <![CDATA[Y axis not responding and loose belts]]> https://www.soliforum.com/post/123671/#p123671 Hi, me again.

I'm trying to troubleshoot a loose belt on a S3 and S4, but for some reason, manual control keeps not working.  I get if the belt is loose the mount won't move, but normally that involves the motor at least trying to move and making a grunting noise.  When I do manual control and tell it to try, it just doesn't respond.  X and Z work fine, and I can get it to go to y-home, but it just won't even respond if I tell it to try to move in the y direction.

Even when the loose belt is fixed, the commands don't do anything on repeter host.  Any help on this would be appreciated.

]]> Thu, 02 Jun 2016 21:55:41 +0000 https://www.soliforum.com/post/123671/#p123671