<![CDATA[SoliForum - 3D Printing Community — HotEnd and Bed Temperature Not Correct]]> https://www.soliforum.com/topic/14320/hotend-and-bed-temperature-not-correct/ Sat, 19 Mar 2016 00:50:04 +0000 PunBB <![CDATA[Re: HotEnd and Bed Temperature Not Correct]]> https://www.soliforum.com/post/119537/#p119537 Thanks for the help.
I have a new 1.0A replacing w/ E3D. Ill compare the 2 when finished.

I looked into what's involved w/ writing tables, unfortunately, its beyond my understanding.

]]> Sat, 19 Mar 2016 00:50:04 +0000 https://www.soliforum.com/post/119537/#p119537 <![CDATA[Re: HotEnd and Bed Temperature Not Correct]]> https://www.soliforum.com/post/119468/#p119468 I think you could also make your own custom table.

]]> Thu, 17 Mar 2016 22:53:12 +0000 https://www.soliforum.com/post/119468/#p119468 <![CDATA[Re: HotEnd and Bed Temperature Not Correct]]> https://www.soliforum.com/post/119467/#p119467 You could bridge it and that bypass it without removing it. there are a few ways to easily bridge it. one would be to solder a wire across both ends this way is easy to remove o wire in a switch that you can chose to turn on and bridge or leave off and make the resister be used.

another way is to solder bridge it.

]]> Thu, 17 Mar 2016 22:52:31 +0000 https://www.soliforum.com/post/119467/#p119467 <![CDATA[Re: HotEnd and Bed Temperature Not Correct]]> https://www.soliforum.com/post/119421/#p119421 Is there a way to bypass the 10k resistor w/ out physically removing ?

or I could write on DaV, -35C  hmm

]]> Thu, 17 Mar 2016 05:55:47 +0000 https://www.soliforum.com/post/119421/#p119421 <![CDATA[Re: HotEnd and Bed Temperature Not Correct]]> https://www.soliforum.com/post/119420/#p119420 I have not. I just use table 5 with the e3dv6 and it is fine for me

]]> Thu, 17 Mar 2016 03:29:11 +0000 https://www.soliforum.com/post/119420/#p119420 <![CDATA[Re: HotEnd and Bed Temperature Not Correct]]> https://www.soliforum.com/post/119417/#p119417 I found this on Voltivo:
https://forum.voltivo.com/showthread.ph … amp;page=2
Post #39

It seems to relate to my issue.

Has anyone done this method ?

]]> Thu, 17 Mar 2016 03:04:02 +0000 https://www.soliforum.com/post/119417/#p119417 <![CDATA[HotEnd and Bed Temperature Not Correct]]> https://www.soliforum.com/post/119408/#p119408 HotEnd reads 215C, actual 180C
Bed reads 80C, actual 70C

I will take more temp reads at diff levels, but

where and how to adjust the temperature in firmware ?

In configuration.h it has...
// What type of sensor is used?
// 5 is userdefined thermistor table 0
#define EXT0_TEMPSENSOR_TYPE 5

further down
#define HEATED_BED_SENSOR_TYPE 6

]]> Thu, 17 Mar 2016 01:37:22 +0000 https://www.soliforum.com/post/119408/#p119408