<![CDATA[SoliForum - 3D Printing Community — Temperature Control Problems]]> https://www.soliforum.com/topic/1388/temperature-control-problems/ Sat, 23 Feb 2013 19:06:47 +0000 PunBB <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13764/#p13764 I have created a Wiki page on this topic here:

http://www.soliwiki.com/PID_tuning

]]> Sat, 23 Feb 2013 19:06:47 +0000 https://www.soliforum.com/post/13764/#p13764 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13732/#p13732 Of course lol I can print turn bed and extruder on off etc I see eveerything but send doesnt seem to work


Also while on Calibration I notice the echo: the accel values are 9000 and 10000 is this too high? I saw another ost where they recommended 3000?

]]> Sat, 23 Feb 2013 14:28:50 +0000 https://www.soliforum.com/post/13732/#p13732 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13730/#p13730 Make sure your SD is in the 'Connected' state and that you see the message in the bottom log window.

]]> Sat, 23 Feb 2013 14:22:56 +0000 https://www.soliforum.com/post/13730/#p13730 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13723/#p13723 dumb question how do I send M303 command? I tried in RH from print menu. Typed in hit send, i tried in gcode screen and hit run nothing

]]> Sat, 23 Feb 2013 13:07:01 +0000 https://www.soliforum.com/post/13723/#p13723 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13670/#p13670 Thanks Nicky,  Guess the same issue here but only I'm using WIN8.  I saw the PID and saved them to EEPROM.  now waiting for bed to heat so I can test

]]> Fri, 22 Feb 2013 23:02:57 +0000 https://www.soliforum.com/post/13670/#p13670 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13669/#p13669 ya that happened to me after my autotune (OS X 1.8.3). I just disconnected the printer in RH, unplugged and plugged back in and reconnected. I then saw it echo the old PID values.

I then sent my M301 command with the new values and sent a M500 command to save.  I disconnected and reconnected to the printer again in RH and saw it echo back the new values.

]]> Fri, 22 Feb 2013 22:56:48 +0000 https://www.soliforum.com/post/13669/#p13669 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13667/#p13667 Tried to do autotune and I get the following and it just keeps sending the same error.

Anyone seen this RESEND 90: error before?

17:26:09.938 : echo:PID settings:
17:26:09.938 : echo:   M301 P22.20 I1.08 D114.00
17:29:43.114 : PID Autotune start
17:33:51.219 : bias: 103 d: 103 min: 195.82 max: 206.11
17:34:48.753 : bias: 95 d: 95 min: 195.90 max: 204.96
17:35:45.132 : bias: 93 d: 93 min: 195.94 max: 204.15
17:35:45.132 : Ku: 28.83 Tu: 56.36
17:35:45.132 : Clasic PID
17:35:45.132 : Kp: 17.30
17:35:45.132 : Ki: 0.61
17:35:45.132 : Kd: 121.87
17:36:40.715 : bias: 91 d: 91 min: 196.56 max: 204.15
17:36:40.715 : Ku: 30.53 Tu: 55.58
17:36:40.715 : Clasic PID
17:36:40.715 : Kp: 18.32
17:36:40.715 : Ki: 0.66
17:36:40.715 : Kd: 127.27
17:37:35.612 : bias: 92 d: 92 min: 196.56 max: 203.75
17:37:35.659 : Ku: 32.59 Tu: 54.92
17:37:35.659 : Clasic PID
17:37:35.659 : Kp: 19.56
17:37:35.659 : Ki: 0.71
17:37:35.659 : Kd: 134.26
17:37:35.659 : PID Autotune finished ! Place the Kp, Ki and Kd constants in the configuration.h
17:37:38.436 : Error:checksum mismatch, Last Line:89
17:37:38.436 : Resend:90
17:37:41.509 : Error:Line Number is not Last Line Number+1, Last Line:89
17:37:41.509 : Resend:90
17:37:44.568 : Error:Line Number is not Last Line Number+1, Last Line:89
17:37:44.568 : Resend:90
17:37:47.625 : Error:Line Number is not Last Line Number+1, Last Line:89
17:37:47.625 : Resend:90
17:37:50.683 : Error:Line Number is not Last Line Number+1, Last Line:89
17:37:50.683 : Resend:90
17:37:53.741 : Error:Line Number is not Last Line Number+1, Last Line:89
17:37:53.741 : Resend:90
17:37:56.798 : Error:Line Number is not Last Line Number+1, Last Line:89
17:37:56.798 : Resend:90
17:37:59.856 : Error:Line Number is not Last Line Number+1, Last Line:89
17:37:59.856 : Resend:90
17:38:02.913 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:02.913 : Resend:90
17:38:05.971 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:05.971 : Resend:90
17:38:09.029 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:09.029 : Resend:90
17:38:12.086 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:12.086 : Resend:90
17:38:15.144 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:15.144 : Resend:90
17:38:18.202 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:18.202 : Resend:90
17:38:21.259 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:21.259 : Resend:90
17:38:24.317 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:24.317 : Resend:90
17:38:27.375 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:27.375 : Resend:90
17:38:30.436 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:30.436 : Resend:90
17:38:33.493 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:33.493 : Resend:90
17:38:36.551 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:36.551 : Resend:90
17:38:39.609 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:39.609 : Resend:90
17:38:42.666 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:42.666 : Resend:90
17:38:45.724 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:45.724 : Resend:90
17:38:48.782 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:48.782 : Resend:90
17:38:51.839 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:51.839 : Resend:90
17:38:54.897 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:54.897 : Resend:90
17:38:57.954 : Error:Line Number is not Last Line Number+1, Last Line:89
17:38:57.954 : Resend:90

]]> Fri, 22 Feb 2013 22:40:45 +0000 https://www.soliforum.com/post/13667/#p13667 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13553/#p13553 Everything makes more sense about this EEPROM stuff. I was always worried about how I would verify if it actually saved.

Then I just noticed that when I connect RH to the printer it spits back all of these settings everytime.  2 teachable moments in 1! 

echo:Marlin 1.0.0
echo: Last Updated: 2012-09-17 | Author: Lawsy
echo: Free Memory: 952  PlannerBufferBytes: 1232
echo:Stored settings retreived:
echo:Steps per unit:
echo:  M92 X88.00 Y88.00 Z2268.00 E135.00  <- whoops, I'm pretty sure this isnt the right stepper value that I wanted for extruder calibration
echo:Maximum feedrates (mm/s):
echo:  M203 X500.00 Y500.00 Z5.00 E45.00
echo:Maximum Acceleration (mm/s2):
M201 X9000 Y9000 Z100 E10000
echo:Acceleration: S=acceleration, T=retract acceleration
echo:  M204 S3000.00 T3000.00
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s),  Z=maximum Z jerk (mm/s)
echo:  M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
echo:Home offset (mm):
echo:  M206 X0.00 Y0.00 Z0.00
echo:PID settings:
echo:   M301 P28.20 I1.64 D126.55 my new PID values

]]> Fri, 22 Feb 2013 02:53:43 +0000 https://www.soliforum.com/post/13553/#p13553 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13551/#p13551 Since I sill have 10.5.8 on my mac it won't run RH so for now I just use some old dell laptops I have laying around

BTW I have not actually tried the about mcodes but they should work ... in theory smile

]]> Fri, 22 Feb 2013 02:34:34 +0000 https://www.soliforum.com/post/13551/#p13551 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13550/#p13550 ronsii wrote:

Looked around... and voila

once you get the PID numbers..

issue a 'M301 Pxx.xx Ix.xx D xxx.xx

then issue a 'M500' to save to eeprom

jackpot. thank you! marking this thread as a favorite for future reference.

]]> Fri, 22 Feb 2013 02:32:32 +0000 https://www.soliforum.com/post/13550/#p13550 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13549/#p13549 ronsii wrote:

You don't???

I believe it is a possible issue with mac.

When i received my SD2 back in october, I followed the installation instructions found here:
http://www.solidoodle.com/mac-instructions/

And I had to manually install the Arduino drivers from the site listed on that instruction page.

I would bet that might have something to do with it,

]]> Fri, 22 Feb 2013 02:31:54 +0000 https://www.soliforum.com/post/13549/#p13549 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13548/#p13548 Looked around... and voila

once you get the PID numbers..

issue a 'M301 Pxx.xx Ix.xx D xxx.xx

then issue a 'M500' to save to eeprom

]]> Fri, 22 Feb 2013 02:29:18 +0000 https://www.soliforum.com/post/13548/#p13548 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13547/#p13547 nickythegreek wrote:

I had no idea that this was a thing and it could explain some colored banding that I have observed several times.

Any idea how I would set the output numbers thru gcode since I dont have the EEPROM Config settings in my RH?


You don't???

]]> Fri, 22 Feb 2013 02:23:12 +0000 https://www.soliforum.com/post/13547/#p13547 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13546/#p13546 I had no idea that this was a thing and it could explain some colored banding that I have observed several times.

Any idea how I would set the output numbers thru gcode since I dont have the EEPROM Config settings in my RH?

EDIT:
Would I just put that in my start gcode?

]]> Fri, 22 Feb 2013 02:20:35 +0000 https://www.soliforum.com/post/13546/#p13546 <![CDATA[Re: Temperature Control Problems]]> https://www.soliforum.com/post/13283/#p13283 for once I beat someone smile LOL

]]> Wed, 20 Feb 2013 00:37:56 +0000 https://www.soliforum.com/post/13283/#p13283