SoliForum - 3D Printing Community — Repetier problems on 1.0a

Re: Repetier problems on 1.0a

null@example.com (luc) — Sat, 09 Apr 2016 07:25:37 +0000

you have 1.0A this behaviour happen when you use 1.0 FW. 0.91 is not for 1.0A, only 0.92 support it
I see you can revert back to stock FW, it means you use 1.0 FW and not 1.0A FW
It means also you use wrong setting in configuration in repetier
Be sure you set MODEL 1 in repetier (change / save / close / reopen to verify change is done) before flashing

Re: Repetier problems on 1.0a

null@example.com (bigrednurse) — Sat, 09 Apr 2016 05:31:33 +0000

Just installed repetier 0.91 on my davinci 1.0a with win 10 could not install 0.92 Anyway after install can not move z axis up. Have tried setting home position to max, -200 200 inverting the z axis. Seems to me i'm on the limit switch and it is inverted.
Did anyone else have this problem after making the switch. Ya I did not think to home all axis BEFORE SHORTING J37 even reverting to the stock firmware has the same problem.
If I knew which connectors were for the limit switches I would switch them but short of tearing down the whole machine...
Can somebody help.

Re: Repetier problems on 1.0a

null@example.com (luc) — Wed, 06 Apr 2016 20:50:23 +0000

using bossac with stock FW on AiO / 1.0A/ 2.0A make printer unusable because FW is encrypted for these printers

Contact support or flash repetier

Re: Repetier problems on 1.0a

null@example.com (daimellah_mhamed) — Wed, 06 Apr 2016 19:06:24 +0000

Hello everybody,

Please, please help me:

I have a DA VINCI 1.0 AIO, I tried to make a firmware downgrade from 1.2 to 1.1.3 by bossac, my printer still not working.
How can I solve this isuue.

Thanks in advance.

Re: Repetier problems on 1.0a

null@example.com (snu) — Wed, 02 Mar 2016 15:26:01 +0000

milojaimes007 wrote:

I just flashed my xyz da Vinci 1.0 AiO and I'm trying to print PLA
I seem to have got jammed and extruder feed wheels jammed I cleared jam and cleaned wheels but now I can't get wheels to turn again
I love repetier so far much better firmware and first hack too super excited and feeling a bit lost

Start a new thread, you'll be more likely to get an answer. I can try to help you through PM if you want.

Re: Repetier problems on 1.0a

null@example.com (milojaimes007) — Wed, 02 Mar 2016 02:25:45 +0000

I just flashed my xyz da Vinci 1.0 AiO and I'm trying to print PLA
I seem to have got jammed and extruder feed wheels jammed I cleared jam and cleaned wheels but now I can't get wheels to turn again

I love repetier so far much better firmware and first hack too super excited and feeling a bit lost

Re: Repetier problems on 1.0a

null@example.com (bld59rt) — Wed, 24 Feb 2016 16:31:07 +0000

snu wrote:

I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.

Glad to hear that repetier is working on the new 1.0A model. I also am right on the fence of flashing mine. Was just concerned about reading online that it was not working properly with the 1.0A 3F10A.
Which version did you use? Thanks Dave

Re: Repetier problems on 1.0a

null@example.com (carl_m1968) — Thu, 21 Jan 2016 08:16:40 +0000

Morgan wrote:

I have problem after installing repetier firmware
I experience too much material comes out during print
Any nody has solutions for me?

Have you done all your basic calibration? Like extruder steps per mm?

Re: Repetier problems on 1.0a

null@example.com (Morgan) — Thu, 21 Jan 2016 08:09:12 +0000

I have problem after installing repetier firmware
I experience too much material comes out during print
Any nody has solutions for me?

Re: Repetier problems on 1.0a

null@example.com (snu) — Wed, 13 Jan 2016 19:24:38 +0000

That seems to have worked. I was so used to not having to use glue with the XYZ firmware that I forgot about it. Printing perfectly now!

Re: Repetier problems on 1.0a

null@example.com (carl_m1968) — Wed, 13 Jan 2016 18:46:30 +0000

snu wrote:

I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.

So you mean they are not sticking to the bed then? Try a light coat of aquanet hairspray on the bed, or Elmers purple glue stick on the bed..

Repetier problems on 1.0a

null@example.com (snu) — Wed, 13 Jan 2016 18:22:32 +0000

I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.