SoliForum - 3D Printing Community — not sticking to print bed

Re: not sticking to print bed

null@example.com (Landin81) — Fri, 18 Dec 2015 03:48:10 +0000

I have my bed set to 85 degree celcius. I put the glue on when its gets up to around 60-70 degrees.

If you have "biltema" in your country their gluestick works great

Re: not sticking to print bed

null@example.com (heartless) — Fri, 18 Dec 2015 03:18:00 +0000

i use Aqua Net on glass for everything - PLA and ABS.

used to use the glue stick, but finally gave up on that - the hairspray lasts longer.

Re: not sticking to print bed

null@example.com (widespreaddeadhead) — Thu, 17 Dec 2015 14:39:54 +0000

For PLA I use Aquanet Extra hold and I love the glass finish on the bottom of my prints. For ABS, Elmer's purple glue stick was the only thing the prevented my edges from warping.

Re: not sticking to print bed

null@example.com (dedafmonteur) — Wed, 16 Dec 2015 17:43:48 +0000

I use 3DLAC, it's awesome.

Re: not sticking to print bed

null@example.com (slimstar2) — Wed, 16 Dec 2015 04:22:40 +0000

I just got the 200mm x 200mm square plate and use paper clips to hold as I did with my glass plates

Re: not sticking to print bed

null@example.com (carl_m1968) — Wed, 16 Dec 2015 03:48:34 +0000

slimstar2 wrote:

Hi guys, its been awhile but I am back . I just bought and received this new build plate from GeckoTek 3d. I haven't printed anything really large yet but so far the results are good . No spray no cleanup seems to hold very well so far. A bit pricy but worth it if it works well. $39.00

Price depends on your printer, for mine they want $85.. I think I will stick with swappable glass and hairspray.

Re: not sticking to print bed

null@example.com (slimstar2) — Wed, 16 Dec 2015 03:38:10 +0000

Hi guys, its been awhile but I am back . I just bought and received this new build plate from GeckoTek 3d. I haven't printed anything really large yet but so far the results are good . No spray no cleanup seems to hold very well so far. A bit pricy but worth it if it works well. $39.00

Re: not sticking to print bed

null@example.com (grob) — Wed, 16 Dec 2015 03:10:09 +0000

My top temp is not confirmed, it's probably a bit under 100. I'd guess you're right.

Re: not sticking to print bed

null@example.com (carl_m1968) — Wed, 16 Dec 2015 00:57:30 +0000

grob wrote:

I've used both over a long and tumultuous struggle with adhesion. As Az says, the temperature is important. If you can't get the bed up over 100C or so, the hairspray... IT DOES NOTHING!
Glue is a bit more tolerant.

I run Aquanet at 75 on my bed which has been confirmed and parts stick like they are part of the bed until they cool then they slid or lift right off. Could also be the type of glass your bed has.

Re: not sticking to print bed

null@example.com (grob) — Wed, 16 Dec 2015 00:48:20 +0000

I've used both over a long and tumultuous struggle with adhesion. As Az says, the temperature is important. If you can't get the bed up over 100C or so, the hairspray... IT DOES NOTHING!

Glue is a bit more tolerant.

Re: not sticking to print bed

null@example.com (mdrVB6) — Tue, 15 Dec 2015 13:14:40 +0000

Personally, I've gotten much better results with purple glue stick than hairspray but I seem to be the exception. With glue stick, I don't have to mask off my rods and extruder so it makes a lot less mess and doesn't make your work area smell like a hair salon. I put it on while the bed is heating and let it dry to a slight haze before starting the print. I usually get impatient and start my print by the time the bed hits 70 C and even with a large case type print that takes up the whole bed, I can get no lifting. Of course, the first step must be to level your bed and get the correct nozzle distance from the bed for the first layer, regardless of adhesion method.

Re: not sticking to print bed

null@example.com (AZERATE) — Tue, 15 Dec 2015 01:12:58 +0000

^purple elmers glue.
Alternatively, you could buy some Aqua Net Extra Hold or any other hairspray with vinyl copolymer...thats the sweet spot for ABS. Aqua Net and glass are a match made in maker heaven!

Glue may require a different bed temp setting in my experience. 85c for glue, 97-110c for hairspray with said contents.

Re: not sticking to print bed

null@example.com (carl_m1968) — Tue, 15 Dec 2015 00:37:04 +0000

kb9asu wrote:

using abs material, and a glass bed. question is when do you put the glue stick on, when the print bed is cold or hot??? printer is a davinci pro, put a glass heat bed on it, like that better, no tape to mess with. so why do the prints let lose?? any ideas??

You use the glue when the bed is cool. However the glue the machine comes with is garbage. You need to go out and get Elmers Purple glue sticks. They work much better. Even better if you can find Aquanet hairspray in your area, use it. Just mask the rods and extruder then spray a light coat over the glass. let it dry and it will be good for 10+ prints. Just let it cool fully and the part should lift right off.

not sticking to print bed

null@example.com (kb9asu) — Mon, 14 Dec 2015 23:48:59 +0000

using abs material, and a glass bed. question is when do you put the glue stick on, when the print bed is cold or hot??? printer is a davinci pro, put a glass heat bed on it, like that better, no tape to mess with. so why do the prints let lose?? any ideas??