<![CDATA[SoliForum - 3D Printing Community — printing problems]]> https://www.soliforum.com/topic/13067/printing-problems/ Sat, 12 Dec 2015 16:07:10 +0000 PunBB <![CDATA[Re: printing problems]]> https://www.soliforum.com/post/111447/#p111447 Sounds like you are experiencing a PSU interruption.  Most likely a bad connection at the board but it could also be a bad connection right in the PSU itself.  My bet is the problem is right at the barrel connector.

]]> Sat, 12 Dec 2015 16:07:10 +0000 https://www.soliforum.com/post/111447/#p111447 <![CDATA[Re: printing problems]]> https://www.soliforum.com/post/111433/#p111433 are you getting any errors in the log?

]]> Sat, 12 Dec 2015 14:41:31 +0000 https://www.soliforum.com/post/111433/#p111433 <![CDATA[Re: printing problems]]> https://www.soliforum.com/post/111383/#p111383 now it wont even print, itll warm up and start to print like the configuration and then it will just shut down

]]> Fri, 11 Dec 2015 16:17:07 +0000 https://www.soliforum.com/post/111383/#p111383 <![CDATA[Re: printing problems]]> https://www.soliforum.com/post/111382/#p111382 thanks it didnt end up printing properly after a while

]]> Fri, 11 Dec 2015 15:50:17 +0000 https://www.soliforum.com/post/111382/#p111382 <![CDATA[Re: printing problems]]> https://www.soliforum.com/post/111337/#p111337 Keep us posted. There could be a number of reasons why you experiencing this. It sounds like you are experiencing shifting and while it could be from dry motion, it would be obvious from the noise of screeches and clanks.
Fortunately, if it is another problem, it IS fixable! smile

]]> Thu, 10 Dec 2015 18:51:07 +0000 https://www.soliforum.com/post/111337/#p111337 <![CDATA[Re: printing problems]]> https://www.soliforum.com/post/111335/#p111335 I believe that it works again.  to trouble shoot this, I lubed up the poles with white lithium grease. and if that doesnt work see if you can move the belt over a little bit so the gears arent in the same grooves over and over again.  I believe that was what the problem was.

]]> Thu, 10 Dec 2015 18:43:36 +0000 https://www.soliforum.com/post/111335/#p111335 <![CDATA[Re: printing problems]]> https://www.soliforum.com/post/111331/#p111331 djmatt182 wrote:

I have a solidoodle4.  When i go to print something, itll start the outline of it and pause at points and then keep going.  It then gets set off course after that thinking that it is still on course and will then start printing more to the right making it end up lobsided.  Im new to the 3d printing to.  Also when it goes in to fill a layer, it will start fine and then it will start making lines that go all over the place.  Ive seen it print properly before and its not printing how it used to.  Any thoughts on why it might be doing this?


Does this happen with different models or just one?

]]> Thu, 10 Dec 2015 18:20:18 +0000 https://www.soliforum.com/post/111331/#p111331 <![CDATA[printing problems]]> https://www.soliforum.com/post/111330/#p111330 I have a solidoodle4.  When i go to print something, itll start the outline of it and pause at points and then keep going.  It then gets set off course after that thinking that it is still on course and will then start printing more to the right making it end up lobsided.  Im new to the 3d printing to.  Also when it goes in to fill a layer, it will start fine and then it will start making lines that go all over the place.  Ive seen it print properly before and its not printing how it used to.  Any thoughts on why it might be doing this?

]]> Thu, 10 Dec 2015 18:18:44 +0000 https://www.soliforum.com/post/111330/#p111330