SoliForum - 3D Printing Community — Ramps 1.4 with LCD and SD support

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Sat, 30 Jan 2016 03:59:41 +0000

Problem solved, thanks to help from Wardjr and Ironman.

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Wed, 09 Dec 2015 16:21:41 +0000

For those that are following this thread, the solidoodle is a 24 volt system and the ramps is 12 volts. To cure this issue, I have swapped over to a 12 headed bed, 12 extruder heater, and a 12 volt atx power supply.

Re: Ramps 1.4 with LCD and SD support

null@example.com (wardjr) — Wed, 09 Dec 2015 16:07:25 +0000

Lots of other thoughts check your PM

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Wed, 09 Dec 2015 14:56:52 +0000

Ok so heres an update. I have follow all the supplied links you guys offered. Some nice information. But unfortunately, I still do not have a working printer. I manually figured out the steps per unit and with solidoodle saying it should be 400, that means my z stepper is a 1/4 and it had a 2mm z screw. I have not see any other manufacture use a 2mm pitch. So I measured it, it came out to two then I punched in the numbers 200x4=800/2(pitch)= 400. So I removed the two outer jumpers to make it a 1/4 step. I tried the z axis and nothing. I change the firmware to 400, and all it does is light tap/click but doesn't move. I can hook the z axis motor to the x or y driver and it moves fine. I swap the driver from one to the other and z control still doesn't work. As far as the end stops I believe I have them figured out. I used the original firmware to modify the one I am using. I can home y and x, but after they click the switch and home then they are very sporatic moving the other direction. I have to cycle the power to get them to move again. Possible I have a bad component.
Any other thoughts would be appreciated.

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Wed, 09 Dec 2015 00:20:56 +0000

Thank you I will try that when I'm back around my printer

Re: Ramps 1.4 with LCD and SD support

null@example.com (carl_m1968) — Tue, 08 Dec 2015 23:06:22 +0000

Z should always be 1/8 if it is a screw drive.. You will not see any difference in 1/16 to 1/32 on the Z since it simply controls the layer height it will have no real impact on precision or print quality.

Re: Ramps 1.4 with LCD and SD support

null@example.com (android78) — Tue, 08 Dec 2015 22:40:52 +0000

Sorry. I just read back and saw that you've suggested 1/16 microsteps setting. One ting I found is that the same jumper setting is not the same results for all stepper drivers. So make sure you are looking at the correct table for the driver.
http://3dtek.xyz/blogs/technical-docs/1 … s-tutorial

I would certainly try a lower steps per unit of the z axis anyway.

Re: Ramps 1.4 with LCD and SD support

null@example.com (IronMan) — Tue, 08 Dec 2015 21:00:50 +0000

2268 should not be too high...see this link:

http://www.soliforum.com/post/51771/#p51771

You can try 400, but your Z movement will be scaled down greater than 5 times...

Re: Ramps 1.4 with LCD and SD support

null@example.com (android78) — Tue, 08 Dec 2015 20:43:48 +0000

I would think that the 2268 could cause the Z to not move. Such a high number could mean it is trying to do steps too quickly and essentially miss every step. Try setting it to 400 and see if it works.

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Tue, 08 Dec 2015 16:29:34 +0000

So what are your thoughts on my next step? I do have a question about the endstops. How are they suppose to work. They will be open allowing the motor to move until a motor hits it and stops it. Then for the other direction it should also be open and it will stop a prescribed amount of MM then stop at that point? If so I can try to figure out the combination I need. Also do I need to work with changing the endstop in the firmware to state open when the switch is not activated? I assume the motors should be moving toward the X and Y axis endstops and also moving toward 0 and when move away from endstop it should be travel toward 200.
Another question I have is the actual steps per movement of the motors. The firmware we are using have a different setup. It states:
DEFAULT_AXIS_STEPS_PER_UNIT {88,88,2268,138}
where as my original press firmware states: DEFAULT_AXIS_STEPS_PER_UNIT {80,80,400,96.09355} would this cause the studdering of the stepper motors or non movement at all on the z axis? Ill be in an out all day today so once you respond I will try what you think we should do.
Thanks

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Mon, 07 Dec 2015 20:45:12 +0000

jagowilson wrote:

hold up. are X+ and Y+ actually working? reading triggered when pressed, reading open when not?

If they are hooked up to the min m119 says min open max triggered if I hit the switch and run m119 min and max are both triggered. Not sure if that helps.

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Mon, 07 Dec 2015 20:39:49 +0000

I didn't realize the time, I have to head to work in about 30 min. Will you be available to continue to help tomorrow?
And thank you for your help so far,
Don

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Mon, 07 Dec 2015 20:30:53 +0000

I guess I am not understanding that would you have a drawing or would it be possible to call you?or I can try taking a picture of my board and you can edit it to show me?

Re: Ramps 1.4 with LCD and SD support

null@example.com (jagowilson) — Mon, 07 Dec 2015 20:26:58 +0000

Only jump these:
X-
Y-
Z+ (unless this is taken up by a switch, I'm not familiar with auto leveling)

Plug switches into these:
X+
Y+
Z-

Re: Ramps 1.4 with LCD and SD support

null@example.com (sandcub1971) — Mon, 07 Dec 2015 20:23:29 +0000

yes if I leave them hooked up and press the switch they read.
if I disconnect them and install jumpers as you said this is what I come up with:
are the just set backward in the firmware?
MIN jumped on x/y

x min open
x max triggered
x moves 1 direction them makes a slight pop and whistling sound
y min open
y max triggered
y moves 1 direction them makes a slight pop and whistling sound

Max jumped on x/y
x min triggered
x max open
x moves other direction them makes a slight pop and whistling sound
y min triggered
y max open
y moves other direction them makes a slight pop and whistling sound

no jumpers
x/y both min/max triggered no movement